577363

Benning IT 110 Manual

33
Zoom out
Zoom in
Previous page
1/80
Next page
33
Step 3 Followtheconnectiondiagramshowningure5.15(seethechapterContact voltage)
to perform trip-out time measurement.
Step 4 Check the displayed warnings and online voltage/terminal monitor before starting the
measurement. If OK, press the TEST key. After performing, the measurement results
with PASS/FAIL indication appear on the display.
Fig. 5.18: Example of trip-out time measurement results
Displayed results:
t: Trip-out time
Uc: Contact voltage
Save displayed results for documentation purposes. Refer to chapter 6.1 for further information on
setting functions and saving of measurement results. (BENNING IT 120 B only)
Note:
- Parameters set in this function are also kept for other RCD functions.
- RCD trip-out time measurement will be performed only if contact voltage at nominal differential
current is lower than the set limit contact voltage.
- The measurement of contact voltage in pre-test does not normally trip an RCD. However, the
triplimitmaybeexceededasaresultofleakagecurrentowingtothePEprotectiveconductor
or via a capacitive connection between L and PE conductors.
5.3.8 Trip-out current (RCD )
An ever increasing fault current serves to test the limiting sensitivity for the FI/RCD tripping. The
device increases the testing current in small steps over the whole range as follows:
RCD type
Increasing fault current
Wave form
Initial value Final value
AC 0.2×I
∆N
1.1×I
∆N
Sine AC
A, F (I
∆N
≥30mA) 0.2×I
∆N
1.5×I
∆N
Pulsating
A, F (I
∆N
= 10 mA) 0.2×I
∆N
2.2×I
∆N
B, B+ 0.2×I
∆N
2.2×I
∆N
Direct current DC
ThemaximumtestingcurrentisID(trippingcurrent)orequalsthenalvalue,iftheFI/RCDhasnot
tripped.
How to perform trip-out current measurement:
Step 1 Select FI/ RCD TEST (RCD) with the function selector switch. Use the keys / to se-
lect Trip-out current (RCD). The following menu is displayed:
Fig. 5.19: Trip-out current measurement menu
Connect the test cable to the BENNING IT 110/ BENNING IT 120 B.
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning IT 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning IT 110 in the language / languages: English as an attachment in your email.

The manual is 6,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Benning IT 110

Benning IT 110 User Manual - German - 83 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info