577300

Benning Duspol Expert Manual

8
Zoom out
Zoom in
Previous page
1/63
Next page
01/2014
DUSPOL
®
expert
8
phase) on. Protective clothing and insulating conditions on site
might impair the function.
8. Continuity test(gureH)
- Thecontinuity test must becarried out on systemparts
whicharefreeofvoltage.Ifnecessary,capacitorshaveto
be discharged.
- ApplythetwoprobetipsL1/-
2
and L2/+
3
tothesystem
parts to be tested.
- Incaseofcontinuity(R<100kΩ),anacousticsignalis
emittedandtheyellowLEDΩ
M
forcontinuitylightsup.
-
This function also can be used to determine the conducting
and non-conducting direction of semiconductor components.
- If a voltage is applied to the test point, the voltage tester
automatically switches over to the voltage test function
and indicates this function.
9. Cable break detector (gureI)
- The cable break detector is intended for the non-contact
localization of cable breaks on exposed live lines.
-
FullygraspthedisplayhandleL2
8
and pass the detector
5
over a live line (e.g. a cable reel or a chain of lights) from the
feeding point (phase) in direction of the other end of the line.
- Aslongasthelineisnotinterrupted,theyellowLEDΩ
M
forcontinuityisflashing.
- The point of the cable break has been localized as soon as
theyellowLEDΩ
M
goes out.
Note:
The cable break detector can be used in earthed mains from
230V,50Hz/60Hz(phasetoearth)on.Protectiveclothing
and insulating conditions on site might impair the function.
10. Measuring point illumination(gureJ)
- The measuring point illumination
4
can be switched on
withtheprobetipsbeingopenbyactuatingthepush-but-
ton
6
ofthedisplayhandleL2
8
(1 second).
- Theoffautomaticallyafter10seconds.
11. Battery replacement(gureK)
- Donotapplyvoltagetothedevicewhenthebatterycom-
partment is open!
- Thebatterycompartmentislocatedonthebackofthedis-
playhandleL2
8
.
- Unscrew the screw of the battery compartment cover
andreplacetheusedbatteriesbytwonewmicrobatter-
ies (LR03/ AAA). Make sure that the new batteries are
insertedwithcorrectpolarity!
- Placethebatterycompartmentcoverontothedisplayhan-
dle L2
8
and tighten the screw.
12. Technical data
- regulation:DINEN61243-3:2011,IEC61243-3:2009
- nominalvoltagerange:12Vto1,000VAC/DC
- nominalfrequencyrangef:0to500Hz
- max. indication error: U
n
±15%,ELVU
n
+0%-15%
- internalresistanceofmeasuringcircuit:175kΩ,
- current consumption of measuring circuit: I
S
< 6,0 mA
(1.000V)
- current consumption of load circuit: I
S
<550mA(1,000V)
- polarityindication:+24VLED,-24VLED,+12VLED,-
12VLED(withpush-buttonsbeingactuated)
- polarityindication:+12VLED,-12VLED
- external conductor (phase indication) test and phase se-
quencetest:≥U
n
230V,50/60Hz
- continuitytest:0to100kΩ,LED+buzzer,testingcurrent:
max.10μA
- cablebreakdetector:≥U
n
200V
- vibrationmotor,start:≥U
n
230V
- overvoltagecategory:CATIV600V,
CATIII1,000V
-
protectioncategory:IP65(DINVDE0470-1IEC/EN60529)
6 - first index: protection against access to dangerous
parts and protection against solid impurities, dustproof
5 - second index: protected against water jets. The device
can also be used in the rain.
- max.allowableDutycycle:30s(max.30seconds),240s
off
- battery:2xmicro,LR03/AAA(3V)
- weight: approx. 250g
- length of connecting cable: approx. 1,000 mm
- operating temperature and storage temperature range:
-15°Cto+55°C(climaticcategoryN)
- times of controlled reduction (thermal protection):
voltage/time:230V/30s,400V/9s,690V/5s,1000V/2s
- responsetimeofthedisplay:750ms
13. General maintenance
Cleantheexteriorofthedevicewithacleandrycloth.
Ifthereiscontaminationordepositsintheareaofthebattery
orthebattery housing, clean theseareasas well by means
ofadrycloth.
If the device is stored for a longer period of time, remove the
batteries from the device!
14. Environmental protection
Please lead batteries and also the device at the end
of its useful life to the available return and collection
systems
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning Duspol Expert at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning Duspol Expert in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info