588384
65
Zoom out
Zoom in
Previous page
1/85
Next page
134
FRENI A DISCO
DISC BRAKES
FREINS A DISQUE
SCHEIBENBREMSEN
FRENOS DE DISCO
Verifica usura e sostituzione pastiglie
L'usura delle pastiglie dei freni a disco anteriore deve
essere controllata al primo tagliando e successiva
mente ogni 6000 Km. Ricordati che utilizzando il
veicolo su strade sporche e/o bagnate l'usura delle
pastiglie è maggiore e pertanto il controllo va effet
tuato con maggiore frequenza.
Posiziona il veicolo sul cavalletto.
FRENO ANTERIORE: rimuovi il coperchio della
pinza 1 (fig. 1) facendo leva con un giravite,
FRENO POSTERIORE: effettua il controllo visiva
mente sul freno posteriore 2 (fig. 2).
Non azionare la leva del freno dopo aver
rimosso la pinza freno
perche potrebbe causare la fuoriuscita dei
pistoncini dalle proprie sedi, con conseguente perdita di
liquido freni. Nello sfilare la pinza dal disco freno, porre la
massima attenzione a non danneggiare i tubi che
contengono il liquido freni.
Controlla lo spessore del materiale d'attrito. Se lo spessore
è ridotto a 1 mm o meno, rivolgiti immediatamente ad un
Concessionario o Officina Autorizzata Benelli per effettuare
la sostituzione.
Nel rimontare la pinza del freno a disco
è necessario applicare alle
viti una coppia di serraggio di 20-23 Nm.
Il mancato controllo della coppia di serraggio può
pregiudicare la sicurezza del veicolo.
Checking and replacing the brake pads
Check the wear of the front and rear brake pads on the
first servicing, and then every 6.000 km. If the vehicle is
mostly used on dirty and/or wet roads, the brake pads
wear more rapidly and must be checked at shorter
intervals.
Place the vehicle on the stand.
FRONT BRAKE Lever off caliper cover 1 (fig. 1)
with a screwdriver.
REAR BRAKE Check the brake 2 visually (fig. 2).
Do not operate the brake lever
after the wheel has been removed as
this will cause the pistons to come out of
their seat and fluid leakage. When removing the cali
per from the brake disc, be careful not to damage
the pipes containing the brake fluid.
Check the thickness of the linings. If they are 1 mm thick
or less, immediately contact a Benelli Dealer or Authorized
Workshop to have the brake pads replaced.
On refitting the caliper of the disc
brake, make sure to tighten the screws
with the prescribed torque of 20-23 Nm.
Failure to respect the torque values may compromise
the vehicle's safety.
MANUTENZIONE MAINTENANCE
Fig. 1
Fig. 2
2
1
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benelli Velvet 125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benelli Velvet 125 in the language / languages: English as an attachment in your email.

The manual is 3,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info