747162
4
Zoom out
Zoom in
Previous page
1/4
Next page
If Try this
The receiver seems to be turned o
The battery is depleted. Charge or replace it with a VARTA V40H NiMH battery.
The battery LED blinks in yellow
The battery level is low. Charge or replace it with a VARTA V40H NiMH battery.
The receiver is not charging
Check that the receiver is placed correctly in the charger and that the power supply
is connected. The mains LED and charging LED should be lit.
Charge or replace the backup batteries with four 1.2 V NiMH rechargeable batteries.
The receiver does not respond
when a transmitter is activated
Check the transmitter batteries and connections.
Move the receiver closer to the transmitter to make sure it’s within radio range.
Check that the receiver is set to the same radio key as the other units in the Visit
system, see Changing the radio key.
The receiver is activated for no
apparent reason
There is probably another Visit system installed nearby that triggers your system.
Change the radio key on all units, see Changing the radio key.
The bed shaker does not vibrate
Check that the bed shaker is connected and that the receiver is placed in the charger.
Advanced programming
By using advanced programming, you can customize the signal pattern from a specic transmitter and event, displaying
the LED colour and vibration pattern of your choice. The advanced programming overrides the radio key and pairs the
units via the serial number. Please note that smoke alarms cannot be programmed for safety reasons.
Note: The transmitter must be activated as it is intended to be used in the system to generate the right signal.
This means that you can’t always use the transmitter test button (see Default signal pattern for the relevant transmitter).
Here is how you program the wrist receiver:
1 Press and hold the function button on the receiver. The green and yellow Visit LEDs will start to blink alternately.
While still holding down the button, activate the desired transmitter as intended. The battery LED on the receiver lights
up in yellow to show that you are in advanced programming mode. Release the button.
2 Scroll through the dierent Visit LED options by pressing the function button on the receiver. Select the desired Visit
LED colour by holding down the function button until the battery LED goes out and lights up again.
3 Scroll through the dierent vibration options by pressing the function button on the receiver. Select the desired
vibration pattern by holding down the function button until the battery LED goes out and lights up again.
4 The wrist receiver will now show the new Visit LED colour and vibration pattern. Press the function button briey to end
the demonstration. After a short while, it will return to normal mode.
Deleting the advanced programming
Follow the procedure below to delete the advanced programming.
1 Hold down the function button on the receiver until the green and yellow Visit LEDs blink alternately. Release the button.
2 Press the function button on the receiver 3 times in quick succession.
3 All Visit LEDs will light up for ~2 seconds to show that it has been deleted.
Troubleshooting
Most problems with the wrist receiver can be solved quickly by following the advice below.
Visit wrist receiver
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bellman Visit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bellman Visit in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info