747164
8
Zoom out
Zoom in
Previous page
1/11
Next page
Radio module features
This smoke alarm is equipped with a radio module that:
Transmits radio signals to up to 40 interconnected smoke alarms.
Transmits radio signals to one or several supplementary Visit receivers. A Visit receiver
will help hard of hearing and deaf people to notice the alarm. The alert type and signal
pattern for the Visit receiver is found in the products user manual.
Radio channel/key
This smoke alarm transmits on a xed radio channel/radio key. So, no matter what radio
key your Visit receiver is set to, it will respond to the alarm if it’s within radio range.
Radio range
The operation range between a smoke alarm and an interconnected unit or Visit receiver is
over 100 m free eld but is inuenced by the thickness of the walls and the wall materials in
the house or apartment. The range will also be also be reduced if the smoke alarm battery
level is low. Check that the Visit receivers and interconnected units responds to the smoke
alarm signal everywhere in the house or apartment. The bedroom is most important.
1514
Test and maintenance
Your smoke alarm is a life saving device and should be tested periodically. Regularly check
that the red LED on the smoke alarm blinks every 40 s to show that the unit is powered.
Testing your smoke alarms
It is recommended that you test your smoke alarms after installation and then at least
weekly to ensure the units are working.
Press and hold the test button until the alarm sounds. If there is no sound, the battery,
horn or circuity could be defected, please read the 'Troubleshooting' section for advice.
If you have interconnected smoke alarms, they will sound for 10s and blink fast for 5 min.
To mute them, press the test button on each unit.
If the smoke alarm is connected to a supplementary Visit receiver, check and make sure
that the Visit receiver reacts too. See the 'Quick start guide' section and the Visit receiver
user manual. The Visit receiver will stop signalling within 40s.
Repeat this procedure for all non-interconnected smoke alarms in the system.
Warning: Do not test with an open ame. You could damage the alarm or ignite combustible
materials and start a re. When you press the test button it simulates the eect of smoke in a
smoke alarm which it could experience in a real re. So, there is no need to test smoke alarms
with smoke or ame.
Cleaning your smoke alarm
Clean your smoke alarm regularly. Use a soft bristle brush or the brush attachment of your
vacuum cleaner to remove dust and cobwebs from the side slots where the smoke enters.
To clean the cover, wipe with a damp cloth and dry thoroughly.
Important: Do not attempt to remove the cover to clean the inside. This will aect warranty.
Warning: Do not paint your smoke alarm. Other than the maintenance and cleaning described
in this leaet, no other customer servicing of this product is required. Repairs, when needed,
must be performed by the manufacturer.
Inteconnected smoke alarms
Cause Status LED Sound
Alarm Chirps twice every s
Low battery Blinks once every 3 h Chirps once every 3 h
Test Blinks twice every s Chirps twice every s
Signal pattern – interconnected units
Depending on the cause of the alarm, the interconnected smoke alarms will signal as follows:
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bellman BE1289 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bellman BE1289 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info