772320
8
Zoom out
Zoom in
Previous page
1/86
Next page
6
(e.g. on a car roof, on a towed trailer or behind a motorhome).
Periodically check the bike: tyres, brakes, lights, etc.
Periodically wash the child seat with soap and water. Do not use aggressive substances.
MOUNTING THE CHILD SEAT
!!! Do not carry out mounting operations with the child in the seat.
Make sure you have all the components before proceeding with assembly (g. A).
Mounting the support bracket
Take the back rack off the bike if it interferes with mounting the seat.
Mount the support bracket on the bicycle frame as illustrated in g. B. Make sure that the arrows printed
on the front side of the block are pointing upwards.
!!! WARNING: mount the brace on the bicycle frame and not on the pipe under the bicycle saddle.
!!! WARNING: check that the brake and gear cables do not interfere with the bracket (1).
Choose the best screws (6) for your frame (see Table 1). (If the screws that come with the seat are too
short, longer ones [M6x80, for instance] can be found in a hardware store).
Slip the screws (6) into their holes.
Tighten the nuts slightly and evenly (7) (g. C).
The support bracket must be free to slide along the tube: it will be tightened once the seat is in the
correct position (see xing the child seat to the bike).
Fixing the support fork to the child seat
Turn the seat over.
Position the U-bend of the support fork (9) under the ap (g. D). Place the tool in its slot.
Line up the hole on the welded post (9) with the hole in the seat.
Slip the bolt (11) through the plate (10), the holes in the child seat, and the welded bracket (g. E).
Fully tighten the nut (12) (g. F).
Fixing the child seat to the bike
Hold down the yellow button on the bracket (2). Insert the support fork (8) into the upper part of the
bracket (1) (g. G).
!!! WARNING: once inserted, make sure that the yellow button pops out (2). If it doesn’t the fork
(8) is not inserted correctly: repeat the operation.
Check that the child seat does not interfere with pedals, brakes, gears and other moving parts on the bike.
Leave enough room for the child’s legs.
Line the child seat up with the bike’s axis.
Fully tighten the screws (6) on the bracket after having found the best position for the seat.
!!! WARNING: periodically check that the screws are tight. They may loosen with use.
Taking the child seat off the bike
Hold down the yellow button (2) on the bracket and pull up the support fork (8) up and off (g. G).
Installing the foot rests
Take the left foot rest (13) (marked SX on the back).
Push it into the vertical slot on the left leg.
Push up as far as possible (g. H).
Take the blocking lever (15) for the left foot rest (marked SX on the back).
Push the blocking lever into the hole behind the rest. Insert from the outside and push right in (g. I).
Close the blocking lever by pushing downwards until you hear a click (g. L).
Repeat the same operations for the right foot rest (marked DX).
EN
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bellelli Standard at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bellelli Standard in the language / languages: All languages as an attachment in your email.

The manual is 10.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info