Manual Bell Hitchbiker 4 (page 6 of 20) (English, French, Spanish)

773382

Zoom out

Zoom in

1/20

Installation

1. Wipe or brush out the inside of your receiver hitch so it’s free from road

debris. Figure A.

2. Insert the rack until the threaded hole lines up with the hole in the side

of the receiver tube. To accommodate the 11

/4" receiver hitches simply

remove the insert C-shim screw and C-shim. Figure B.

3. Insert the attachment bolt and tighten. ALWAYS insert the bolt from the

drivers side – this will improve the stability of the rack in the hitch. Using

the vertical mast for leverage wiggle the rack back and forth. Check and

tighten the attachment bolt more if needed. Install the butterfly pin into

the hole on the end of the attachment bolt. Figure C.

4. Install the lower hitch post to the vertical mast. Line up the holes, insert

and attach the lower frame bolts, washers and nuts. Tighten. Figure D.

5. Install the support arm assembly. Line up the holes, insert and attach

the upper frame bolts, washers and nuts. Tighten. Figure E.

6. On level ground, check that the support arms are angled up from the

horizontal. If they are angled down from the horizontal away from the

car, do not load the rack. Your hitch should be adjusted by a hitch mount

professional before the rack can be used safely. Figure F.

(Included on Folding Racks ONLY)

Check the tilt pivot by removing the

pivot pin and folding the rack away from the car. The rack should move

freely down far enough to clear back hatches and tailgates on most cars.

There should only be a minimal amount of play in the pivot bolt – if there

is substantial play check the pivot bolt and nut for tightness. Make note

of the clearance distance between your vehicle door and the mast. Tilt the

mast back into the vertical position and reinstall the pivot pin and retainer

clip. Figure G, H and I. LOAD BIKES ONTO INDIVIDUAL CRADLES. TIGHTEN ALL

STRAPS TO TOP OR SEAT TUBES, USING THE CRADLES. Figures M, N, and O.

8. To raise the rack arms remove security pin from locking clip. Remove

locking clip from the mast. Raise the rack arms and re-insert locking pin

through the mast and attach security pin. Figure J and K.

9. Load the first bike with your chain side facing away from the vehicle.

Alternating the direction of the bikes makes the carrier easier to load and

prevents the handlebars from getting tangled.

English

J K LI

DCA

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bell Hitchbiker 4 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1.01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bell Hitchbiker 4 Manual

Product: