773366

Bell Dashboard 300 Manual

24
Zoom out
Zoom in
Previous page
1/34
Next page
24
instalaciÓn
PASO 1: Instale la pila – Quite la tapa de la pila de la parte inferior del ciclocomputador mediante el uso de una
moneda pequeña (Figura 1). Instale la pila del ciclociclocomputador (3.0 V/CR2032) con el polo positivo (+) hacia
arriba. Vuelva a instalar la tapa de la pila y apriétela. Nota: El reemplazo de la pila borrará toda la información alma-
cenada. Al instalar una pila nueva después de haber utilizado el ciclocomputador, asegúrese de escribir la lectura del
odómetro antes de cambiar la pila para posteriormente volver a introducir la lectura en el ciclocomputador.
PASO 2: Instale el imán en la rueda – Fije el imán a un rayo en el lado derecho de la rueda delantera (Figura
2). Asegúrese que el imán está orientado hacia el exterior de la rueda de tal manera que el lado plano del imán pasa
por el frente del sensor.
PASO 3: Fixation du capteur sur la fourche – Fixer le capteur du compteur kilométrique sur le montant droit
de la fourche, à l'aide de deux des attaches de câble fournies. Vérier que le côté métallique du capteur soit face
à la roue. Ne pas serrer dénitivement les attaches de câble à ce stade, car il pourra peut-être s’avérer nécessaire
d’ajuster l’emplacement du capteur (Figura 3). Ajuster l’emplacement du capteur et de l’aimant pour que l’écart
entre les deux ne soit pas plus grand que 2 mm (Figura 4). L’aimant doit alors passer devant l’extrémité du capteur
lorsque la roue tourne.
PASO 4: Instale el soporte de montaje y el ciclocomputador – Fije el soporte de montaje al manubrio
mediante el uso de las dos (2) bridas de plástico aún disponibles tal como se muestra en la (Figura 4). Asegúrese
que el soporte de montaje está rmemente jado y no se deslizará por el manubrio. Inserte el ciclocomputador en el
soporte de montaje (Figura 5). Una vez hechos todos los ajustes y que el ciclocomputador funciona correctamente,
apriete rmemente todas las tuercas y pernos.
Sensor
or Magnet
5mm
Sensor
Magnet
Sensor
Top View
Bicycle fork
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bell Dashboard 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bell Dashboard 300 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1.14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info