Manual Belion GK604VG20 (page 5 of 21) (English, German, Dutch, French, Italian, Polish, Portuguese, Turkish, Spanish)

630722

Zoom out

Zoom in

1/21

3. Bringen Sie die Verteiler und Brennerdeckel auf den entspre-

chenden Kochstellen an und setzen Sie die Roste korrekt in

den entsprechenden Halteelementen ein.

B) Einstellung der Gashähne (Abb. 8):

1. Drehen Sie die Bedienknebel auf die niedrigste Stufe.

2. Ziehen Sie die Bedienknebel der Gashähne ab. Es wird eine

Knebeldichtung aus flexiblem Gummi sichtbar. Drücken Sie

diese mit der Schraubendreherspitze beiseite, um an die Ein-

stellschraube des Gashahns zu gelangen.

Bauen Sie die Knebeldichtungen niemals aus. Die Dichtun-

gen sind für den fehlerfreien Betrieb des Geräts unerlässlich,

da sie das Eindringen von Flüssigkeiten und Schmutz ins Ge-

räteinnere verhindern.

3. Stellen Sie die minimale Gaszufuhr ein, indem Sie die Bypass-

Schraube mit einem Schlitzschraubenzieher drehen.

Je nach Gasart, auf die Sie umstellen (siehe Tabelle III), müs-

sen entsprechende Schritte durchgeführt werden:

A: die Bypass-Schrauben ganz anziehen.

B: die Bypass-Schrauben bis zum korrekten Gasaustritt an den

Brennern lockern.

C: die Bypass-Schrauben müssen von einem autorisierten

Fachmann ausgetauscht werden.

D: nehmen Sie keine Veränderungen an den Bypass-Schrau-

ben vor.

Stellen Sie sicher, dass der Brenner bei einer Umstellung des

Bedienknebels von der höchsten auf die niedrigste Stufe nicht

ausgeht und nicht zurückschlägt.

Wenn Sie nicht an die Bypass-Schraube gelangen sollten,

bauen Sie die Fettauffangschale, die mit dem restlichen Koch-

feld mittels eines Clip-Befestigungssystems und Schrauben ver-

bunden ist, aus. Zum Abnehmen gehen Sie wie folgt vor:

1. Nehmen Sie alle Roste, Brennerdeckel, Verteiler und Bedien-

knebel ab.

2. Lockern Sie die Brenner-Schrauben.

3. Verwenden Sie ggf. den bei unserem Kundendienst erhältli-

chen Demontagehebel 483196. Lösen Sie die vordere Clip-Be-

festigung, indem Sie den Hebel in den markierten Bereichen

ansetzen. Abb. 9.

4. Für den Wiedereinbau des Geräts folgen Sie den Ausbauan-

weisungen in umgekehrter Reihenfolge.

Bauen Sie niemals die Achse des Gashahns aus (Abb. 10). Bei

einer Störung den kompletten Gashahn ersetzen.

Installation instructions

Safety precautions

Read the appliance's instructions before installing and using.

The images shown in these instructions are for guidance only.

The manufacturer is exempt from all responsibility if the

requirements of this manual are not complied with.

This appliance must only be used in well ventilated places. It

must not be connected to a combustion product removal

device.

All operations relating to installation, connection, regulation

and conversion to other gas types must be carried out by an

authorised installation engineer, respecting all applicable

regulations, standards and the specifications of the local gas

and electricity suppliers. Special attention shall be paid to

ventilation regulations.

It is recommended you contact the Technical Assistance

Service to change to another gas type.

This appliance has been designed for home use only, not for

commercial or professional use. This appliance cannot be

installed on yachts or in caravans. The warranty will only be valid

if the appliance is used for the purpose for which it was

designed.

Before installing, you need to check that local distribution

conditions are compatible with the appliance's adjustment

indicated on the specifications plate (gas type and pressure,

power, voltage). See table I.

Before you begin, turn off the appliance's electricity and gas

supply.

The supply cable must be attached to the unit to prevent it from

touching hot parts of the oven or hob.

Appliances with electrical supply must be earthed.

Do not tamper with the appliance's interior. If necessary, call our

Technical Assistance Service.

Before installing

This appliance is class 3 type, according to the EN 30-1-1

regulation for gas appliances: built-in appliance.

The kitchen unit in which the appliance is installed must be

properly secured and stable.

The kitchen units next to the appliance, the laminated covering

and glue for adhering it must be made of non-flammable and

heat-resistant materials.

This appliance cannot be installed above fridges, washing

machines, dishwashers or similar.

An oven must have forced ventilation to install a hob above it.

Check the dimensions of the oven in the installation manual.

If an extractor fan is installed, you must follow the instructions in

the installation manual, always respecting the minimum vertical

distance from the hob (fig. 1).

Preparation of the kitchen unit (fig. 1-2)

Make an appropriate size cut in the work surface.

If the hob is electric or mixed (gas and electricity) and there is

no oven below, place a non-flammable separator (e.g. metal or

plywood) 10 mm from the bottom of the hob. This will prevent

access to the base of the hob.If the hob is gas, it is

recommendable to place the separator at the same distance.

On wood work surfaces, varnish the cutting surfaces with a

special glue. This protects them from moisture which could

collect under the work surface.

Installation of appliance

Depending on the model, the adhesive seal may be factory-

fitted. If this is the case, it should not be removed under any

circumstances, since the adhesive seal prevents leaks. If the

seal has not been factory-fitted, apply it to the underside of the

hob. Fig. 3.

Fitting the appliance onto the kitchen unit:

1. Screw each one of the clips into the position indicated so that

they are free to rotate.

2. Insert and centre the hob.

Press the sides of the hob until it is supported around its entire

perimeter.

3. Turn the clips and tighten them fully.

The position of the clips depends on how thick the work

surface is. Fig. 4.

Removal of hob

Turn off the appliance's electricity and gas supply.

Unscrew the clips and proceed in the reverse order to

installation.

Gas connection (fig. 5)

The end of the inlet connection point of the gas hob has a 1/2”

(20.955 mm) thread that allows for:

■ fixed connection.

■ connection using a flexible metal pipe (L min. 1 m -

max. 3 m).

The watertight seal supplied or available from the technical

assistance service (code 034308) must be inserted between

the manifold outlet and the gas supply.

You must prevent the pipe from coming into contact with

moving parts of the kitchen unit (for example, a drawer) and

prevent access to any spaces which might become obstructed.

If you need to connect the gas supply horizontally, our technical

assistance service can supply you with an L-tube

(code 173018), and a seal (code 034308).

If you need to make a cylindrical connection, replace the factory-

fitted L-tube with the one in the accessory bag supplied or

available from the technical assistance service (code 529649).

Fig. 5a.

Please remember to insert the seal.

: Danger of leaks!

If any connection is handled, check the seal.

The manufacturer is not liable for any connection leaking, after

being handled.

Electric connection (fig. 6)

Check that the voltage and power of the appliance are

compatible with the electrical installation.

The hobs are supplied with a power cable with or without a wall

socket plug.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Belion GK604VG20 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Belion GK604VG20

Belion GK604VG20 User Manual - Dutch - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Belion GK604VG20 Manual

Product: