757479
7
Zoom out
Zoom in
Previous page
1/60
Next page
Washing Machine / User Manual 7 / EN
4.1 Installation
Apply to the nearest authorised service agent for the installation of your product.
Preparation of the location and electrical, tap water and waste water installations at the place of
installation is under customer's responsibility.
Make sure that the water inlet and discharge hoses as well as the power cable are not folded,
pinched or crushed while pushing the product into its place after installation or cleaning
procedures.
Make sure that the installation and electrical connections of the product are performed by
authorised service. Manufacturer shall not be held liable for damages that may arise from
procedures carried out by unauthorised persons.
Prior to installation, visually check if the product has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
4.1.1 Approprate nstallaton locaton
Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other
similar surfaces.
When the washing machine and dryer are placed on top of each other, their total weight –when
loaded– amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient
load carrying capacity!
Do not place the product on the power cable.
Do not install the product in the environments where the temperature falls below 0 ºC.
Leaving a gap at the sides of the machine is suggested to reduce vibration and noise
On a graduated floor, do not place the product next to the edge or on a platform.
Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use
them on the product.
4.1.2 Removng packagng renforcement (If the product has)
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by pulling the
ribbon. Do not make this operation alone by yourself.
4.1.3 Removng the transportaton locks
1 Loosen all bolts with an appropriate wrench until they turn freely.
2 Remove the transport safety bolts by turning them slightly.
3 Insert the plastic covers in the bag containing the user manual to the openings on the rear
panel.
A
CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the
product will be damaged.
C
Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again
in the future.
Install the transport safety bolts in reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WTV6611BC1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WTV6611BC1 in the language / languages: English, German as an attachment in your email.

The manual is 3,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BEKO WTV6611BC1

BEKO WTV6611BC1 User Manual - Dutch, French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info