757481
6
Zoom out
Zoom in
Previous page
1/56
Next page
6 / EN Washing Machine / User Manual
4.1 Installation
Apply to the nearest authorised service
agent for the installation of your product.
Preparation of the location and electrical,
tap water and waste water installations at
the place of installation is under customer's
responsibility.
Make sure that the water inlet and discharge
hoses as well as the power cable are not
folded, pinched or crushed while pushing
the product into its place after installation or
cleaning procedures.
Make sure that the installation and electrical
connections of the product are performed
by authorised service. Manufacturer shall
not be held liable for damages that may
arise from procedures carried out by
unauthorised persons.
Prior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products cause
risks for your safety.
4.1.1 Appropriate installation location
Place the product on a hard and level floor.
Do not put it onto a carpet with high pile or
other similar surfaces.
When the washing machine and dryer are
placed on top of each other, their total
weight –when loaded– amounts to 180 kg.
Place the product on a solid and flat floor
that has sufficient load carrying capacity!
Do not place the product on the power cable.
Do not install the product in the
environments where the temperature falls
below 0 ºC.
Leaving a gap at the sides of the machine is
suggested to reduce vibration and noise
On a graduated floor, do not place the
product next to the edge or on a platform.
Do not place heat sources such as Hobs,
Irons, Ovens, etc. on the washing machine
and do not use them on the product.
4.1.2 Removing packaging reinforcement
Tilt the machine
backwards to remove the
packaging reinforcement.
Remove the packaging
reinforcement by pulling
the ribbon. Do not make
this operation alone by
yourself.
4.1.3 Removing the
transportation locks
1. Loosen all bolts with an appropriate wrench
until they turn freely.
2. Remove the transport safety bolts by
turning them slightly.
3. Insert the plastic covers in the bag
containing the user manual to the openings
on the rear panel.
A
CAUTION!
Remove the transportation safety bolts
before operating the washing machine!
Otherwise, the product will be damaged.
C
INFORMATION
Keep the transportation safety bolts in
a safe place to reuse when the washing
machine needs to be moved again in the
future.
Install the transport safety bolts in reverse
order of the disassembly procedure.
Never move the product without the
transportation safety bolts properly fixed in
place!
4.1.4 Connecting water supply
C
INFORMATION
It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
A
CAUTION!
Models with a single water inlet should not
be connected to the hot water tap. In such
a case the laundry will get damaged or the
product will switch to protection mode and
will not operate.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WTV10713XWPT1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WTV10713XWPT1 in the language / languages: English, German as an attachment in your email.

The manual is 4,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BEKO WTV10713XWPT1

BEKO WTV10713XWPT1 User Manual - Dutch, French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info