758334

BEKO WTL84111 Manual

8
Zoom out
Zoom in
Previous page
1/32
Next page
8 / EN Washing Machine / User’s Manual
1 Tighten the nuts of the hose by hand.
Never use a tool when tightening the nuts.
2
When hose connection is completed,
check whether there is leak problems at the
connection points by opening the taps fully. If
any leaks occur, turn off the tap remove the
nut. Retighten the nut carefully after checking
the seal. In order to prevent the water leaks
and resultant damages, keep the taps closed
when you do not use the product.
4.1.5 Connecting the drain
hose to the drain
• Attach the end of the drain hose directly to
waste water drain, lavatory or bathtub.
A
CAUTION!
• Your drain house will be flooded if the
hose comes out of its housing during
water discharge. Moreover, there is
risk of scalding due to high washing
temperatures! In order to prevent such
situations and make sure that the machine
performs water intake and discharge
processes without any problem, fix the
drain hose securely.
40 cm
100 cm
• Connect the drain hose to a minimum height
of 40 cm and a maximum height of 100 cm.
• In case the drain hose is elevated after laying
it on the floor level or close to the ground
(less than 40 cm above the ground), water
discharge becomes more difficult and the
laundry may come out excessively wet.
Therefore, follow the heights described in
the figure.
• To prevent the waste water to siphon back
into the machine again and to ensure easy
drainage, do not immerse the end of the
hose into the waste water or do not insert
it into the drain for more than 15 cm. If it is
too long, cut it short.
• The end of the hose should not be bent,
it should not be stepped on and the hose
must not be pinched between the drain and
the machine.
• If the length of the hose is too short, use
it by adding an original extension hose.
Length of the hose may not be longer than
3.2 m. To avoid water leak failures, the
connection between the extension hose and
the drain hose of the product must be fitted
well with an appropriate clamp as not to
come off and leak.
4.1.6 Adjusting the feet
A
CAUTION!
• In order to ensure that the product
operates more silently and vibration-free, it
must stand level and balanced on its feet.
Balance the machine by adjusting the feet.
Otherwise, the product may move from
its place and cause crushing and vibration
problems.
• Do not use any tools to loosen the lock
nuts. Otherwise, they will get damaged.
1 Loosen the lock nuts on the feet by hand.
2 Adjust the feet until the product stands in a
stable and balanced way.
3. Tighten all lock nuts by hand again.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WTL84111 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WTL84111 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info