758343
22
Zoom out
Zoom in
Previous page
1/44
Next page
22 / EN Washing Machine / User’s Manual
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make
must be something that will be carried out after
the programme step that is running. If the change
is not suitable, relevant lights will flash 3 times.
C
INFORMATION
If the machine does not proceed to the
spinning step, the Rinse Hold function
might be active or the automatic
unbalanced load detection system might
be activated due to the unbalanced
distribution of the laundry in the machine.
4.3.14 Loading door lock
There is a locking system on the loading door of
the machine that prevents opening of the loading
door in cases when the water level is unsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. The machine
checks the level of the water inside. If the level is
suitable, the loading door light will turn off and the
loading door can be opened within 1-2 minutes.
If the level is unsuitable, the loading door light
will remain on and the loading door cannot be
opened. If you are obliged to open the loading
door while the Loading Door light is on, you
must cancel the current programme. See
"Cancelling the programme"
Opening the loading door in case of power
failure:
C
INFORMATION
In case of a power failure, you can use the
loading door emergency handle under the pump
filter lid to manually open the loading door.
A
WARNING!
Before opening the loading door, make sure that
there is no water in the machine to avoid flooding.
Water may be hot and could cause scalding.
Turn off and unplug the appliance.
Open the loading door by pulling the loading
door emergency handle downwards.
Try to pull the handle downwards again
if the loading door is not opened.
4.3.15 Changing the selections
after programme has started
Switching the machine to pause mode
Press the Start/Pause to switch the machine
to pause mode while a programme is running.
The light of the current programme will flash on
the Programme Follow-up indicator, indicating
that the machine has switched to pause mode.
Also, when the loading door is ready to be
opened, the Loading Door light will turn off in
addition to the programme step light.
Changing the auxiliary function, speed and
temperature
Depending on the step the programme has
reached, you can cancel or select auxiliary
functions. See “Auxiliary function selection”.
You can also change the speed and
temperature settings. See "Spin speed
selection" and "Temperature selection".
C
INFORMATION
If no change is allowed, the
relevant light will flash 3 times.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WTIK76121 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WTIK76121 in the language / languages: English as an attachment in your email.

The manual is 8,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info