528055

BEKO WMI 71641 Manual

25
Zoom out
Zoom in
Previous page
1/48
Next page
EN
25
Preparation
1. Turn the tap on completely. Check that
the hose is connected tightly.
2. Placethelaundryinthemachine.
3. Add detergent and softener.
Starting
1. Pressthe“On/Off”button.
2. SelecttheProgrammeandthe
temperature.
3. Ifdesired(accordingtoyourmachine’s
model):
– selectanyauxiliaryfunction,
– adjustthespinspeed,
– setthetimedelay,
4. Close the loading door.
5. Press“Start/Pause/Cancel”button.
The display shows the time remaining for
theProgrammetocompleteiftimedelay
is not set.
The display shows the time remaining for
theProgrammetostartifthetimedelayis
set.
6. Check if the Door Locked Symbol
lights up on the screen.
TheDoorLockedSymbol(Figure3-2i)will
light up if time delay is not set.
TheDoorLockedSymbol(Figure3-2i)will
fade if time delay is set.
Cancelling a Programme
1. Pressandholdthe“Start/Pause/
Cancel”buttonforabout3seconds;
the Start symbol will start flashing.
2. The machine can discharge all the
water or can take in water for 3 times
at most to cool down the clothes and
complete discharging process.
Adding more laundry
•
This is only possible under the
followingconditions:
– duringtimedelay,
C
Youmayaddorremovelaundryduring
thetimedelay(untiltheProgramme
starts).Atthebeginningofawashing
cycle(machineallowsaddingmore
laundry during a future step only if the
water level is low enough to open the
loading door or if the temperature in
themachineislow).
In order to add laundry after the start-
upoftheProgramme:
1. Press“Start/Pause/Cancel”button.
2. Opentheloadingdoorandputin
more laundry.
3. Close the loading door.
4. Press“Start/Pause/Cancel”button.
Programme is in rinse hold mode
C
This process is shown with the
flashing spin symbol and the standby
symbol which is lit up.
If you wish to spin when the machine is in
thismode:
1. Adjust the spin speed.
2. Press“Start/Pause/Cancel”button.
TheProgrammecontinues,pumpsout
the water and spins.
3. The standby symbol fades out and the
start symbol lights up.
If you want to discharge the water without
spinning:
1. Press“Start/Pause/Cancel”button.
2. The standby symbol fades out and the
start symbol lights up.
3. TheProgrammecontinuesandonly
pumps out the water.
Re-spinning the laundry
The control system for an unbalanced load
can pause the spinning in cases when the
distribution of the laundry in the drum is
not balanced.
Ifyouwanttore-spintheclothes:
1. Distribute the laundry in your machine
for a balanced load.
2. SelectthespinProgramme.
3. Adjust the spin speed.
After the Programme is finished
Programmeindicatorsymbolsonthe
screenwillremainlitaftertheProgramme
isfinished.“End”willappearonthe
screen.
1. Opentheloadingdoorandtakeout
the laundry when the door locked
symbol on the display fades out.
2. Pressthe“On/Off”button.
3. Turn the water tap off.
4. Remove any folds in the rubber seal
on the loading door and check for
debris.
5. Leave the loading door and detergent
drawer open to dry.
6
Quick instructions for daily use
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WMI 71641 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WMI 71641 in the language / languages: English as an attachment in your email.

The manual is 5,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info