Manual BEKO WMB 81041 LS (page 3 of 52) (English, French)

550079

Zoom out

Zoom in

1/52

has sufficient load carrying capacity!

• Donotplacetheproductonthepowercable.

• Donotinstalltheproductatplaceswhere

temperaturemayfallbelow0ºC.

• Placetheproductatleast1cmawayfromthe

edges of other furniture.

Removing packaging reinforcement

Tiltthemachinebackwardstoremovethe

packaging reinforcement. Remove the packaging

reinforcementbypullingtheribbon.

Removing the transportation locks

 Donotremovethetransportationlocksbefore

taking out the packaging reinforcement.

 Removethetransportationsafetyboltsbefore

operating the washing machine, otherwise, the

productwillbedamaged.

1.Loosenalltheboltswithaspanneruntilthey

rotate freely (C).

2.Removetransportationsafetyboltsbyturning

them gently.

3.AttachtheplasticcoverssuppliedintheUser

Manualbagintotheholesontherearpanel.(P)

 Keepthetransportationsafetyboltsinasafe

place to reuse when the washing machine

needstobemovedagaininthefuture.

Never move the product without the

transportationsafetyboltsproperlyfixedin

place!

Connecting water supply

 Thewatersupplypressurerequiredtorun

theproductisbetween1to10bars(0.1–10

MPa).Itisnecessarytohave10–80litersof

water flowing from the fully open tap in one

minute to have your machine run smoothly.

Attach a pressure reducing valve if water

pressure is higher.

 Ifyouaregoingtousethedoublewater-inlet

productasasingle(cold)water-inletunit,you

must install the supplied stopper to the hot

watervalvebeforeoperatingtheproduct.

(Appliesfortheproductssuppliedwithablind

stopper group.)

 Ifyouwanttousebothwaterinletsofthe

product, connect the hot water hose after

removing the stopper and gasket group from

the hot water valve. (Applies for the products

suppliedwithablindstoppergroup.)

 Modelswithasinglewaterinletshouldnotbe

connectedtothehotwatertap.Insuchacase

the laundry will get damaged or the product will

switch to protection mode and will not operate.

 Donotuseoldorusedwaterinlethoseson

thenewproduct.Itmaycausestainsonyour

laundry.

1.Connectthespecialhosessuppliedwiththe

product to the water inlets on the product. Red

hose(left)(max.90ºC)isforhotwaterinlet,

bluehose(right)(max.25ºC)isforcoldwater

inlet.

Ensure that the cold and hot water connections

are made correctly when installing the product.

Otherwise,yourlaundrywillcomeouthotatthe

end of the washing process and wear out.

2.Tightenallhosenutsbyhand.Neverusea

wrench when tightening the nuts.

3.Openthetapscompletelyaftermakingthehose

connection to check for water leaks at the

connectionpoints.Ifanyleaksoccur,turnoff

the tap and remove the nut. Retighten the nut

carefully after checking the seal. To prevent

waterleakagesanddamagescausedbythem,

keep the taps closed when the machine is not

in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

 Yourhousewillbefloodedifthehosecomes

out of its housing during water discharge.

Moreover, there is risk of scalding due to

high washing temperatures! To prevent such

situations and to ensure smooth water intake

and discharge of the machine, fix the end of the

discharge hose tightly so that it cannot come

out.

• Thehoseshouldbeattachedtoaheightofat

least40cm,and100cmatmost.

• Incasethehoseiselevatedafterlayingitonthe

floor level or close to the ground (less than

40cmabovetheground),waterdischarge

becomesmoredifficultandthelaundrymay

come out excessively wet. Therefore, follow the

heightsdescribedinthefigure.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WMB 81041 LS in the language / languages: English, French as an attachment in your email.

The manual is 3,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

BEKO WMB 81041 LS Manual

Product: