Manual BEKO WMB 51221 C (page 58 of 76) (English, German, Dutch, French)

676601

Zoom out

Zoom in

1/76

 Makesurethatthewaterinletanddischarge

hoses as well as the power cable are not

folded, pinched or crushed while pushing

the product into its place after installation or

cleaning procedures.

Appropriate installation location

• Placethemachineonarigidfloor.Donot

place it on a long pile rug or similar surfaces.

• Totalweightofthewashingmachineandthe

dryer-withfullload-whentheyareplaced

ontopofeachotherreachestoapprox.

180kilograms.Placetheproductonasolid

and flat floor that has sufficient load carrying

capacity!

• Donotplacetheproductonthepowercable.

• Donotinstalltheproductatplaceswhere

temperaturemayfallbelow0ºC.

• Placetheproductatleast1cmawayfromthe

edges of other furniture.

Removing packaging reinforcement

Tilt the machine backwards to remove the

packaging reinforcement. Remove the packaging

reinforcement by pulling the ribbon.

Removing the transportation locks

Do not remove the transportation locks before

taking out the packaging reinforcement.

Remove the transportation safety bolts before

operating the washing machine, otherwise,

the product will be damaged.

1. Loosenalltheboltswithaspanneruntilthey

rotate freely (C).

2. Remove transportation safety bolts by turning

them gently.

3. AttachtheplasticcoverssuppliedintheUser

Manualbagintotheholesontherearpanel.

(P)

 Keepthetransportationsafetyboltsinasafe

place to reuse when the washing machine

needs to be moved again in the future.

 Nevermovetheproductwithoutthe

transportationsafetyboltsproperlyfixedin

place!

Connecting water supply

 Thewatersupplypressurerequiredtorun

theproductisbetween1to10bars(0.1–1

MPa).Itisnecessarytohave10–80litersof

water flowing from the fully open tap in one

minute to have your machine run smoothly.

Attachapressurereducingvalveifwater

pressure is higher.

 Ifyouaregoingtousethedoublewater-inlet

productasasingle(cold)water-inletunit,you

must install the supplied stopper to the hot

water valve before operating the product.

(Appliesfortheproductssuppliedwithablind

stopper group.)

 Ifyouwanttousebothwaterinletsofthe

product, connect the hot water hose after

removing the stopper and gasket group from

thehotwatervalve.(Appliesfortheproducts

supplied with a blind stopper group.)

 Modelswithasinglewaterinletshouldnot

beconnectedtothehotwatertap.Insuch

a case the laundry will get damaged or the

product will switch to protection mode and will

not operate.

Do not use old or used water inlet hoses on

thenewproduct.Itmaycausestainsonyour

laundry.

1. Connectthespecialhosessuppliedwiththe

product to the water inlets on the product.

Redhose(left)(max.90ºC)isforhotwater

inlet,bluehose(right)(max.25ºC)isforcold

water inlet.

Ensure that the cold and hot water

connections are made correctly when

installing the product. Otherwise, your laundry

will come out hot at the end of the washing

process and wear out.

2. Tightenallhosenutsbyhand.Neverusea

wrench when tightening the nuts.

3. Open the taps completely after making the

hose connection to check for water leaks at

theconnectionpoints.Ifanyleaksoccur,turn

off the tap and remove the nut. Retighten

the nut carefully after checking the seal. To

prevent water leakages and damages caused

by them, keep the taps closed when the

machine is not in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

Your house will be flooded if the hose comes

out of its housing during water discharge.

Moreover,thereisriskofscaldingdueto

high washing temperatures! To prevent such

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WMB 51221 C in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

BEKO WMB 51221 C Manual

Product: