556828

BEKO WM74155LW Manual

8
Zoom out
Zoom in
Previous page
1/36
Next page
8
EN
C
Keep the transportation safety bolts
in a safe place to reuse when the
washing machine needs to be moved
again in the future.
C
Never move the product without the
transportation safety bolts properly
fixed in place!
Connecting water supply
C
The water supply pressure required
to run the product is between 1 to 10
bars (0.1 – 10 MPa). It is necessary
to have 10 – 80 liters of water flowing
from the fully open tap in one minute
to have your machine run smoothly.
Attach a pressure reducing valve if
water pressure is higher.
C
If you are going to use the double
water-inlet product as a single (cold)
water-inlet unit, you must install the
supplied stopper to the hot water
valve before operating the product.
(Applies for the products supplied
with a blind stopper group.)
C
If you want to use both water inlets
of the product, connect the hot water
hose after removing the stopper and
gasket group from the hot water
valve. (Applies for the products
supplied with a blind stopper group.)
A
Models with a single water inlet
should not be connected to the hot
water tap. In such a case the laundry
will get damaged or the product will
switch to protection mode and will not
operate.
A
Do not use old or used water inlet
hoses on the new product. It may
cause stains on your laundry.
1. Connect the special hoses supplied
with the product to the water inlets
on the product. Red hose (left) (max.
90 ºC) is for hot water inlet, blue hose
(right) (max. 25 ºC) is for cold water
inlet.
A
Ensure that the cold and hot water
connections are made correctly when
installing the product. Otherwise, your
laundry will come out hot at the end
of the washing process and wear out.
2. Tighten all hose nuts by hand. Never
use a wrench when tightening the
nuts.
3. Open the taps completely after
making the hose connection to check
for water leaks at the connection
points. If any leaks occur, turn off the
tap and remove the nut. Retighten
the nut carefully after checking the
seal. To prevent water leakages and
damages caused by them, keep the
taps closed when the machine is not
in use.
Connecting to the drain
• The end of the drain hose must be
directly connected to the wastewater
drain or to the washbasin.
A
Your house will be flooded if the
hose comes out of its housing
during water discharge. Moreover,
there is risk of scalding due to high
washing temperatures! To prevent
such situations and to ensure smooth
water intake and discharge of the
machine, fix the end of the discharge
hose tightly so that it cannot come
out.
• The hose should be attached to a
height of at least 40 cm, and 100 cm
at most.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WM74155LW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WM74155LW in the language / languages: English as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info