556766
12
Zoom out
Zoom in
Previous page
1/52
Next page
12 / EN
Washing Machine /User’s Manual
Installation
C
Keepthetransportationsafetyboltsinasafe
place to reuse when the washing machine
needs to be moved again in the future.
Never move the product without the
transportation safety bolts properly fixed in
place!
3.4 Connecting water supply
C
The water supply pressure required to run
the product is between 1 to 10 bars (0.1 – 1
MPa). It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
If you are going to use the double water-inlet
product as a single
(cold) water-inlet unit,
you must install the supplied stopper to the
hot water valve before operating the product.
(Applies for the products supplied with a blind
stopper group.)
A
WARNING: Models with a single water inlet
should not be connected to the hot water tap.
In such a case the laundry will get damaged or
the product will switch to protection mode and
will not operate.
WARNING: Do not use old or used water
inlet hoses on the new product. It may cause
stains on your laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product. Red
hose (left) (max. 90 ºC) is for hot water inlet,
blue hose (right) (max. 25 ºC) is for cold water
inlet.
A
WARNING: Ensure that the cold and hot
water connections are made correctly when
installing the product. Otherwise, your laundry
will come out hot at the end of the washing
process and wear out.
2. Tighten all hose nuts by hand. Never use a tool
when tightening the nuts.
3. Open the taps completely after making the
hose connection to check for water leaks at
the connection points. If any leaks occur, turn
off the tap and remove the nut. Retighten the
nut carefully after checking the seal. To prevent
water leakages and damages caused by them,
keep the taps closed when the machine is not
in use.
3.5 Connecting to the drain
•Theendofthedrainhosemustbedirectly
connected to the wastewater drain or to the
washbasin.
•Drainhoseshallbeattachedtoawalldrain,
stand pipe or sink siphon connected to the foul
water drain, do not connect to surface water
drains.
A
WARNING: Your house will be flooded if
the hose comes out of its housing during
water discharge. Moreover, there is risk of
scalding due to high washing temperatures!
To prevent such situations and to ensure
smooth water intake and discharge of the
machine, fix the end of the discharge hose
tightly so that it cannot come out.
•Thehoseshouldbeattachedtoaheightofat
least 40 cm, and 100 cm at most.
•Incasethehoseiselevatedafterlayingiton
the floor level or close to the ground (less than
40 cm above the ground), water discharge
becomes more difficult and the laundry may
come out excessively wet. Therefore, follow the
heights described in the figure.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WI1483 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WI1483 in the language / languages: English as an attachment in your email.

The manual is 4,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info