758298
8
Zoom out
Zoom in
Previous page
1/40
Next page
8 / EN Washing Machine / User Manual
4.1.4 Connecting the water supply
CIt is necessary to have 10 – 80 litres of water flowing from the fully open tap in one minute to have your machine run
smoothly. Attach a pressure reducing valve if the water pressure is higher.
ACAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will
get damaged or the product will switch to protection mode and will not operate.
ACAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge. Moreover, there
is risk of scalding due to high washing temperatures! In order to prevent such situations and make sure that the machine
performs water intake and discharge processes without any problem, fix the drain hose securely.
Connect the drain hose to a minimum height of 40 cm and a maximum height of 100 cm.
In case the drain hose is elevated after laying it on the floor level or close to the ground (less than 40 cm
above the ground), water discharge becomes more difficult and the laundry may come out excessively wet.
Therefore, follow the heights described in the figure.
40 cm
100 cm
To prevent the waste water siphoning back into the machine again and to ensure easy drainage, do not
immerse the end of the hose into the waste water or do not insert it into the drain for more than 15 cm. If it
is too long, cut it short.
The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched
between the drain and the machine.
If the length of the hose is too short, add an original extension hose. Length of the hose may not be longer
than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of
the product must be fitted well with an appropriate clamp as not to come off and/or leak.
4.1.6 Adjusting the feet
ACAUTION: In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced
on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing
and vibration problems.
CAUTION:
Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
1 Loosen the lock nuts on the feet by hand.
2 Adjust the feet until the product stands in a stable and balanced way.
3. Tighten all lock nuts by hand again.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WEY96054 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WEY96054 in the language / languages: English as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info