758239
9
Zoom out
Zoom in
Previous page
1/44
Next page
9 / EN
Washing Machine / User Manual
4.1.7 Electrical connection
Connect the product to a grounded outlet protected by a 13 A fuse. Our company shall not be liable for any
damages that will arise when the product is used without grounding in accordance with the local regulations.
Connection must comply with national regulations.
The wiring for the electrical outlet circuit must be sufficient to meet the appliance requirements. Use of a
Groud Fault Circuit Interrupter (GFCI) is recommended.
Power cable plug must be within easy reach after installation.
If the current value of the fuse or breaker in the house is less than 13 Amps, have a qualified electrician
install a 13 Amp fuse.
The voltage specified in the “Technical specifications” section must be equal to your mains voltage.
Do not make connections via extension cables or multi-plugs.
BWARNING: Damaged power cables must be replaced by Authorised Service Agents.
Electrical requirements
Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the
rating label corresponds to your electricity supply.
We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket
in a readily accessible position.
Should the mains lead of the appliance become damaged or need replacing at any time, it must be replaced
by a special purpose made mains lead which can only be obtained from an Authorised Service Agent.
BWARNING: This appliance must be earthed
If the fitted moulded plug is not suitable for your socket, then the plug should be cut off and an appropriate
plug fitted.
Destroy the old plug, a cut off plug with a bare cord could cause a shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance incorporates a 13A fuse. Should the fuse need to be replaced an ASTA
approved BS1362 fuse of the same rating must be used. Do not forget to refit the fuse cover. In the event of
losing the fuse cover, the plug must not be used until a replacement fuse cover has been fitted. Colour of the
replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are
available from any good electrical store.
Important
Fitting a different plug
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals on your
plug, proceed as follows:
1 Connect the green - yellow or green (earth) wire to the terminal in
the plug marked ‘E’ or with the symbol or coloured green and
yellow or green.
2 Connect the blue (neutral) wire to the terminal in the plug marked
‘N’ or coloured black.
3 Connect the brown (live) wire to the terminal in the plug marked ‘L
or coloured red.
With the alternative plugs a 13A fuse must be fitted either in the plug or
adaptor or in the main fuse box. If in doubt contact a qualified electrician.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WEY84P64E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WEY84P64E in the language / languages: English as an attachment in your email.

The manual is 4,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info