758236
7
Zoom out
Zoom in
Previous page
1/40
Next page
7 / EN
Washing Machine / User Manual
4.1 Installation
Preparation of the location and electrical, tap water and waste water installations at the place of installation
is the customer's responsibility.
Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or
crushed while pushing the product into its place after installation or cleaning procedures.
The manufacturer shall not be held liable for damages that may arise from procedures carried out by
unauthorised persons.
Prior to installation, visually check if the product has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
4.1.1 Appropriate installation location
Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other similar
surfaces.
If the washing machine and dryer are placed on top of each other, their total weight –when loaded–
amounts to 180 kilograms. Place the products on a solid and flat floor that has sufficient load carrying
capacity!
Do not place the product on the power cable.
Do not install the product in environments where the temperature falls below 0 ºC.
Leaving a gap at the sides of the machine is suggested to reduce vibration and noise
On a raised floor, do not place the product next to the edge or on a platform.
Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use them
on the product.
4.1.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement.
Remove the packaging reinforcement that is attached to the ribbon. Do
not attempt this operation alone, get help.
4.1.3 Removing the transportation locks
1 Loose all bolts with an appropriate wrench until they turn freely.
2 Remove the transport safety bolts by rocking them slightly.
3 Insert the plastic covers from the bag containing the user manual into the openings on the rear panel.
ACAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be
damaged.
C
Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.
Install the transport safety bolts in the reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WEX94064E0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WEX94064E0 in the language / languages: English as an attachment in your email.

The manual is 3,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info