758234
32
Zoom out
Zoom in
Previous page
1/40
Next page
32 / EN Washing Machine / User’s Manual
5 Troubleshooting
Problem Cause Solution
Programmes do not start after the
loading door is closed.
Start / Pause / Cancel button is not pressed. Press Start / Pause / Cancel button.
It may be difficult to close the loading door in case of
excessive loading.
Reduce the amount of laundry and make sure
that the loading door is closed properly.
Programme cannot be started or
selected.
The product has switched to self protection mode
due to a supply problem (line voltage, water pressure,
etc.).
To cancel the programme, turn the Programme
Selection knob to select another programme.
Previous programme will be cancelled.
(see.“Cancellation of programme”)
Water inside the product. Some water has remained in the product due to the
quality control processes in the production.
This is not a failure; water is not harmful to the
product.
The product does not take water
in.
Tap is turned off. Turn on the taps.
Water inlet hose is bent. Flatten the hose.
Water inlet filter is clogged. Clean the filter.
Loading door is not closed. Close the door.
The product does not drain water. Water drain hose is clogged or twisted. Clean or flatten the hose.
Pump filter is clogged. Clean the pump filter.
Product vibrates or makes noise. Product is standing unbalanced. Stable the product by adjusting the feet.
A hard substance has entered into the pump filter. Clean the pump filter.
Transportation safety bolts are not removed. Remove the transportation safety bolts.
Laundry quantity in the product is too little. Add more laundry to the product.
Excessive laundry is loaded in the product. Take out some of the laundry from the product
or distribute the load by hand to balance it
homogeneously in the product.
Product is leaning on a rigid item. Make sure that the product is not leaning on
anything.
There is water leaking from the
bottom of the product.
Water drain hose is clogged or twisted. Clean or flatten the hose.
Pump filter is clogged. Clean the pump filter.
Product stopped shortly after the
programme started.
Machine has stopped temporarily due to low voltage. Product will resume running when the voltage
restores to the normal level.
Product directly drains the water
it takes in.
Draining hose is not at adequate height. Connect the water draining hose as described in
the user manual.
No water can be seen in the
product during washing.
Water is inside the invisible part of the product. This is not a failure.
Loading door cannot be opened. Loading door lock is activated because of the water
level in the product.
Drain the water by running the Pump or Spin
programme.
Product is heating up the water or it is at the spinning
cycle.
Wait until the programme completes.
Loading door may be stuck because of the pressure it
is subjected to.
Grab the handle and push and pull the loading
door to release and open it.
If there is no power, loading door of the product will
not open.
To open the loading door, open the pump filter
cap and pull down the emergency handle
positioned at the rear side of the said cap. See
"Loading door lock"
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WEX104064E0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WEX104064E0 in the language / languages: English as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info