817030
12
Zoom out
Zoom in
Previous page
1/56
Next page
12 / EN Washer-Dryer / User Manual
3.3 Removing the transit bolts
A
PRECAUTION!
Do not remove the transit bolts before
removing the packaging reinforcement.
Remove the transit bolts before operating
the washing machine! Otherwise, the
product will get damaged.
3
2
1
1 Use a tool to loosen all bolts
until they rotate freely.
2 Remove the transit bolts by
turning them slightly.
3 Attach the plastic covers supplied in the user
manual bag into the holes on the rear panel.
C
INFORMATION
Keep the transit bolts in a safe place to
reuse when the product needs to be
moved again in the future.
Never move the product without the transit
bolts properly fixed in place!
3.4 Connecting water supply
C
INFORMATION
The water supply pressure required to run
the product is between 1 to 10 bars (0.1
– 1 MPa). It is necessary to have 10 – 80
liters of water flowing from the fully open
tap in one minute to have your product run
smoothly. Attach a pressure reducing valve
if water pressure is higher.
A
CAUTION!
Models with a single water inlet should not
be connected to the hot water tap. In such
a case the laundry will get damaged or the
product will switch to protection mode and
will not operate.
Do not use old or used water inlet hoses
on the new product. It may cause stains on
your laundry.
1 2 3
1 Connect the special hose supplied with the
product to the water inlet on the product.
A
CAUTION!
Ensure that the cold water connection is
made correctly when installing the product.
Otherwise, your laundry will come out hot
at the end of the washing process and
wear out.
2 Tighten the hose nuts securely by hand.
Never use a tool when tightening the nuts.
3 Open the taps completely after making the
hose connection to check for water leaks at
the connection points. If any leak occurs, turn
off the tap and remove the nut. Retighten the
nut carefully after checking the seal. In order
to prevent the water leaks, keep the taps
closed when you do not use the product.
3.5 Connecting to the drain
Attach the end of the drain hose directly
to waste water drain, sink or bathtub.
A
CAUTION!
Your house will be flooded if the
hose comes out of its housing during
water discharge. Moreover, there is
risk of scalding due to high washing
temperatures! To prevent such situations
and to ensure smooth water intake and
discharge of the machine, fix the end of
the discharge hose tightly so that it cannot
displace.
90 cm
90
40
90
40
90 cm
90 cm
min.40
Connect the hose to a minimum height of
40 cm and a maximum height of 90 cm.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WDIK854421F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WDIK854421F in the language / languages: English as an attachment in your email.

The manual is 5.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info