757585
10
Zoom out
Zoom in
Previous page
1/84
Next page
10 / EN Washer-Dryer / User Manual
3 Installation
To make the product ready for use, review the
information in the user manual and make sure
that the electricity, tap water supply and water
drainage systems are appropriate. If they are
not, call a qualified technician and plumber to
have any necessary arrangements carried out.
B
DANGER!
Make sure that the installation and
electrical connections of the product
are performed by competent persons.
Manufacturer shall not be held liable for
damages that may arise from procedures
carried out by unauthorised persons.
DANGER!
Your product is too heavy for one person
to carry.
A
CAUTION!
Prior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products cause
risks for your safety.
A
PRECAUTION!
Preparation of the location and electrical,
tap water and waste water installations at
the place of installation is under customer’s
responsibility.
Make sure that the water inlet and
discharge hoses as well as the power
cable are not folded, pinched or crushed
while pushing the product into its place
after installation or cleaning procedures.
3.1 Appropriate
installation location
Place the product on a solid and level
floor. Do not place it onto a carpet with
high pile or other similar surfaces.
Do not place the product close to the
edge if the floor contains steps. Do not
also place the product on a platform.
Do not place the product on the power cable.
Do not install the product in environments
where the temperature falls below
0 ºC.(See. Warnings for Drying)
Leaving a gap at the sides of the machine
is suggested to reduce vibration and noise
In the area where this product is
installed, there must not be a lockable,
sliding or hinged door that will restrict
the full opening of loading door.
Operate the product in a well ventilated
and dust free environment.
Do not place heat sources such as Hobs,
Irons, Ovens, etc. on the washing machine
and do not use them on the product.
3.2 Removing packaging
reinforcement
Tilt the machine
backwards to remove
the packaging
reinforcement.
Remove the
packaging
reinforcement
attached to the
ribbon.
DANGER!
Your product is heavy. Remove packaging
reinforcement as displayed in the figure.
Be careful not to get your hand caught
under the machine during this procedure.
3.3 Removing the transit bolts
A
PRECAUTION!
Do not remove the transit bolts before
removing the packaging reinforcement.
Remove the transit bolts before operating
the washing machine! Otherwise, the
product will get damaged.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO HTV7732XA01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO HTV7732XA01 in the language / languages: English, German as an attachment in your email.

The manual is 9,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BEKO HTV7732XA01

BEKO HTV7732XA01 User Manual - Dutch, French - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info