112321
11
Zoom out
Zoom in
Previous page
1/27
Next page
Defrosting of the appliance
We advise you to defrost the freezer at
least twice a year or when the ice layer has an
excessive thickness.
The ice build-
up is a normal phenomenon.
The quantity and the rapidity of ice build-
up depends on the ambient conditions and on
the frequency of the door opening.
We advise you to defrost the appliance
when the quantity of frozen food is the least.
Before defrosting, adjust the thermostat
knob to a higher position so that the food
stores more cold.
- Unplug the appliance.
- Take out the frozen food, wrap it in several
sheets of paper and put them in refrigerator or
a cool place.
Take the separator panel and put it under
the freezer in the direction of the dripping
tube. Take out the obstructing plug. The
water which results will be collected in the
special tray (separator panel). After the
melting of the ice and the run-off of the
water please wipe with a cloth
or with a
sponge, then dry well. Put the obstruction
plug back in its place. (Item. 7)
For a fast thaw please leave the door
open.
Do not use sharp metal objects to remove
the ice.
Do not use hairdryers or other electric
heating appliances for defrosting.
Inside cleaning
Before starting the cleaning, unplug the
appliance from the mains.
It is advisable to clean the appliance when
you defrost it.
Wash the inside with lukewarm water
where you add some neutral
detergent. Do
not use soap, detergent, gasoline or acetone
which can leave a strong odour.
Wipe with a wet sponge and dry with a soft
cloth.
During this operation, avoid the excess of
water, in order to prevent its entrance into the
thermal insulation of the appliance, which
would cause unpleasant odours.
Do not forget to clean also the door gasket
especially the bellow ribs, by means of a
clean cloth.
Outside cleaning
Clean the outside of the freezer by means
of a sponge soaked in soapy warm water,
wi
pe with a soft cloth and dry.
The cleaning of the outside part of the
refrigerating circuit (motorcompressor,
condenser, connection tubes) will be done
with a soft brush or with the vacuum
-cleaner.
During this operation, please take care not to
distort the tubes or detach the cables.
Do not use scouring or abrasive materials !
After having finished the cleaning, replace
the accessories at their places and plug in the
appliance.
Replacing the interior light bulb
If the lamp burns out, disconnect the
appliance from the mains. Take out the
lamp trim. Make sure the lamp is
screwed correctly. Plug in the appliance
again. If the lamp still does not go on,
replace it with another one model E14-
15W. Mount back the lamp trim in its
place.
6
GB Instruction for use
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO HSA 13520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO HSA 13520 in the language / languages: Dutch as an attachment in your email.

The manual is 0,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info