757614
8
Zoom out
Zoom in
Previous page
1/24
Next page
8EN
3 Installation
Refer to the nearest Authorised Service Agent
for installation of your product.
C Preparation of location and electrical
installation for the product is under
customer’s responsibility.
BInstallation and electrical connections
must be carried out by a qualified
personnel.
A Prior to installation, visually check if the
product has any defects on it. If so, do
not have it installed. Damaged products
will cause risks for your safety.
Appropriate installation location
Install the product in an environment
which has no risk of freezing and is in a
stable and level position.
Operate your product in a well ventilated,
dust-free environment.
Do not block the air ducts in front of and
under the product with materials such as
long pile rugs and wooden bands.
Do not place your product on a long pile
rug or on similar surfaces.
Do not install the product behind a door
with a lock, sliding door or a hinged door
which can strike the product.
Once the product is installed, it should
stay at the same place where its
connections have been made. When
installing the product, make sure that the
rear wall of it does not touch anywhere
(tap, socket, etc.) and also pay attention
to install the product at a place where it
will stay permanently.
B Do not place the product on top of the
power cable.
Keep at least 1.5 cm distance to walls of
other furniture.
Removing the transportation
safety assembly
ARemove the transportation safety
assembly before using the product for
the first time.
1. Open the loading door.
2. There is a nylon bag inside the drum that
contains a piece of styrofoam. Hold it
from its section marked with XX.
3. Pull the nylon towards yourself and
remove the transportation safety
assembly.
AMake sure that you have removed
the transportation safety assembly
(nylon+styrofoam pieces) before using
the product for the first time. Do not
leave any items inside the drum.
Under counter installation
A special part (Part no. 297 360 0100)
replacing the top trim must be provided
and installed by the Authorised Service
Agent in order to use the machine under
a counter or in a cupboard. It should
never be operated without the top trim.
Leave at least 3 cm of space between
the side and rear walls of the product
and the walls of the counter/cupboard
when installing your product under a
counter or in a cupboard.
Mounting over a washing
machine
A fitting device should be used between
the two machines when installing above
a washing machine. The bracket must
be installed by the Authorised Service
Agent.
Place the product on a firm floor. If
it will be placed on top of a washing
machine, the approximate weight of
both machines may reach 180 kg when
they are full. Therefore, the floor must be
capable of carrying the load on it!
Connection to water drain;
In products equipped with a condenser unit
the water accumulated during the drying
cycle is collected in the water tank. You
should drain the accumulated water after
each washing cycle.
You can directly send the accumulated water
out through the water drain hose supplied
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO DCU 8230 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO DCU 8230 in the language / languages: English as an attachment in your email.

The manual is 1,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info