528065
25
Zoom out
Zoom in
Previous page
1/44
Next page
25
EN
2 Installation
Refer to the nearest Authorised Service Agent for
installation of your product.
C Preparation of location and electrical
installation for the product is under customer’s
responsibility.
BInstallation and electrical connections must be
carried out by a qualified personnel.
A Prior to installation, visually check if the product
has any defects on it. If so, do not have it
installed. Damaged products will cause risks for
your safety.
Appropriate installation location
Install the product in an environment which has
no risk of freezing and is in a stable and level
position.
Operate your product in a well ventilated, dust-
free environment.
Do not block the air ducts in front of and under
the product with materials such as long pile
rugs and wooden bands.
Do not place your product on a long pile rug or
on similar surfaces.
Do not install the product behind a door with a
lock, sliding door or a hinged door which can
strike the product.
Once the product is installed, it should stay at
the same place where its connections have
been made. When installing the product, make
sure that the rear wall of it does not touch
anywhere (tap, socket, etc.) and also pay
attention to install the product at a place where
it will stay permanently.
BDo not place the product on top of the power
cable.
Keep at least 1.5 cm distance to walls of other
furniture.
Removing the transportation safety
assembly
ARemove the transportation safety assembly
before using the product for the first time.
1. Open the loading door.
2. There is a nylon bag inside the drum that
contains a piece of styrofoam. Hold it from its
section marked with XX.
3. Pull the nylon towards yourself and remove the
transportation safety assembly.
A Make sure that you have removed the
transportation safety assembly (nylon+styrofoam
pieces) before using the product for the first time.
Do not leave any items inside the drum.
Under counter installation
A special part (Part no. 297 360 0100) replacing
the top trim must be provided and installed by
the Authorised Service Agent in order to use the
machine under a counter or in a cupboard. It
should never be operated without the top trim.
Leave at least 3 cm of space between the side
and rear walls of the product and the walls of the
counter/cupboard when installing your product
under a counter or in a cupboard.
Mounting over a washing machine
A fitting device should be used between the
two machines when installing above a washing
machine. The bracket (Part no. 297 720 0200
white/297 720 0500 grey) must be installed by
the Authorised Service Agent.
Place the product on a firm floor. If it will be
placed on top of a washing machine, the
approximate weight of both machines may reach
180 kg when they are full. Therefore, the floor
must be capable of carrying the load on it!
Connection to water drain;
In products equipped with a condenser unit the water
accumulated during the drying cycle is collected in
the water tank. You should drain the accumulated
water after each drying cycle.
You can directly send the accumulated water out
through the water drain hose supplied with the
machine instead of periodically draining the water
collected in the water tank.
Connecting the water drain hose;
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO DCU 7330 XB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO DCU 7330 XB in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BEKO DCU 7330 XB

BEKO DCU 7330 XB User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info