582413
24
Zoom out
Zoom in
Previous page
1/32
Next page
24 / EN
Dryer / User Manual
Operating the product
6.12 Progress of programme
Progress of a running programme is shown
through the programme follow-up indicator.
At the beginning of every programme step,
the relevant indicator LED will light up and
light of the completed step will turn off.
“Drying”:
- Drying level will be illuminated during the
whole drying process until the drying degree
reaches “iron dry”.
“Iron Dry”:
- Starts to illuminate when the drying
degree reaches “iron dry” step and remains
illuminated until the next step.
“Cupboard dry”:
Starts to illuminate when the drying degree
reaches “Ready to wear” step and remains
illuminated until the next step.
“Final / Anti-creasing”:
- Illuminates when the programme comes
to an end and anti-creasing function is
activated.
C
If more than one LED light up or
flash concurrently, it means there
is malfunctioning or a failure
(please see, Solution suggestions
for problems).
6.13 Changing the programme
after it has started
You can use this feature to dry your clothes
under higher or lower temperatures after
your dryer has started.
For example;
1. Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to “Cancel”
the programme in order to select “Extra
Dry” programme instead of “Iron Dry”
programme.
2. Select the “Extra Dry” programme by
rotating the programme selection button.
3. Press “Start/Pause/Cancel” button to
start the programme.
C
Press “Start/Pause/Cancel”
button for 3 seconds to cancel
the programme or turn the
programme selection knob in any
direction to end the programme
while the machine is running.
Water tank and filter cleaning
warning lights turn on to warn
the user when the programme is
cancelled by pressing the “Start/
Pause/Cancel” button for 3
seconds. However, the warning
lights do not turn on when
the programme is cancelled by
turning the programme selection
knob. Only the drying light turns
on and the machine remains in
hold until a new programme is
selected and the “Start/Pause/
Cancel” button is pressed. Child-
proof lock of the machine should
not be active in order to perform
these two operations. If the child-
proof lock is active, deactivate
it before performing these
operations.
Adding/removing laundry in standby
mode
In order to add or remove laundry after the
programme starts:
1. Press the “Start/Pause/Cancel” button to
switch the dryer to “Pause” mode. Drying
process will stop.
2. Open the door at “Pause” position and
close it again after adding or taking out
laundry.
3. Press “Start/Pause/Cancel” button to
start the programme.
C
Any laundry added after the
drying process has started may
cause the dried clothes in the
machine intermingle with wet
clothes and the result will be wet
laundry after the drying process
is over.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO DCU 7230 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO DCU 7230 in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BEKO DCU 7230

BEKO DCU 7230 User Manual - German - 28 pages

BEKO DCU 7230 User Manual - Dutch, French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info