Manual BEKO CWB 9710X (page 19 of 28) (English, German, Dutch, French, Italian, Portuguese, Spanish)

677655

Zoom out

Zoom in

1/28

an omnipolar switch with a minimum contact opening of

3 mm must be placed in between the two; its size must

be suitable for the load required and it must comply with

current legislation.

• If the hob is electric, gas, or induction, the minimum distance

between the same and the lower part of the hood must be

at least 65 cm.

If a connection tube composed of two parts is used, the upper

part must be placed outside the lower part. Do not connect

the cooker hood exhaust to the same conductor used to cir-

culate hot air or for evacuating fumes from other appliances

generated by other than an electrical source.Before proceed-

ing with the assembly operations, remove the anti-grease

 lter(s) (Fig.7) so that the unit is easier to handle.

In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

• Fixing to the wall

- Drill the holes A respecting the distances indicated (Fig.2). -

Fix the appliance to the wall and align it in horizontal position

to the wall units.

- When the appliance has been adjusted, de nitely  x the

hood using the screws A (Fig.5).

- For the various installations use screws and screw anchors

suited to the type of wall (e.g. reinforced concrete, plaster-

board, etc.).

If the screws and screw anchors are provided with the product,

check that they are suitable for the type of wall on which the

hood is to be  xed.

• Fixing the decorative telescopic  ue

- Arrange the electrical power supply within the dimensions

of the decorative  ue. If your appliance is to be installed in the

ducting version or in the version with external motor, prepare

the air exhaust opening.

- Adjust the width of the support bracket of the upper  ue

(Fig.3).

- Then  x it to the ceiling using the screws A (Fig.3) in such a

way that it is in line with your hood and respecting the distance

from the ceiling indicated in Fig.2.

- Connect the  ange C to the air exhaust hole using a con-

nection pipe (Fig.5).

- Insert the upper  ue into the lower  ue.

- Fix the lower  ue to the hood using the screws B provided

(Fig.5), extract the upper  ue up to the bracket and  x it with

the screws B (Fig.3).

- If your appliance has the lower connections indicated as in

Fig. 4A, the  xing to be carried out is that shown in Fig. 6A

To transform the hood from a ducting version into a  ltering

version, ask your dealer for the charcoal  lters and follow the

installation instructions.

• Filter hood

Please note:

In order to transform the hood from EXTRACTOR HOOD

into FILTER HOOD the carbon  lters must be ordered at your

distributor as accessory.

We have two different types of Kit, one with extractable carbon

filters (Fig.8) and the other one with re-usable carbon filters

(washable). (Fig.9)

- To replace the extractable active carbon filters X, pull lever

outwards as shown in Fig.8

- To replace re-usable carbon filters Y, remove the brackets

from their seat, pulling them outwards. (Fig.9)

If you find a bracket such as the one indicated in Fig.9a

included in the product packaging, this should be fixed to

the hood using the supplied screws.

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked.

We also recommend that the appliance is left running for

15 minutes after the food is cooked, in order to thoroughly

eliminate all contaminated air.

The e ective performance of the cooker hood depends on

constant maintenance; the anti-grease  lter and the active

carbon  lter both require special attention.

• The anti-grease  lter is used to trap any grease particles

suspended in the air, therefore is subject to saturation (the

time it takes for the  lter to become saturated depends on

the way in which the appliance is used).

- To prevent potential  re hazards, the anti-grease  lters should

be washed a minimum of every 2 months (it is possible to use

the dishwasher for this task).

- After a few washes, the colour of the  lters may change. This

does not mean they have to be replaced.

If the replacement and washing instructions are not followed,

the anti-grease  lters may present a  re hazard.

• The active carbon  lters are used to purify the air which is

released back into the room.

The  lters are not washable or re-usable and must be replaced

at least once every four months.

The active carbon  lter saturation level depends on the fre-

quency with which the appliance is used, the type of cooking

performed and the regularity with which the anti-grease

 lters are cleaned.

• Clean the cooker hood frequently, both inside and outside,

using a cloth which has been dampened with denatured

alcohol or neutral, non-abrasive liquid detergents.

• The light on the cooker hood is designed for use during

cooking and not for general room illumination.

Extended use of the light reduces the average duration of

the bulb.

• Replacing halogen light bulbs (Fig. 10).

To replace the halogen light bulbs B, remove the glass panel

C using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution: do not touch the light bulb with bare hands.

• Replacing halogen light bulbs (Fig. 11).

In order to replace the dichroic lamps, carefully remove

the lamp from the lamp holder with the help of a small  at

screwdriver or a similar tool. PLEASE NOTE! In doing this

operation, please take care not to scratch the hood.

Replace the bulbs with new ones of the same type.

• Commands (Fig.12)

- Luminous (Fig.12A)

- Electronic (Fig.12B)

the key symbols are explained below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

F = AUTOMATIC STOP TIMER - 15 minutes (*)

- 19 -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of BEKO CWB 9710X in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BEKO CWB 9710X

BEKO CWB 9710X User Manual - Dutch - 3 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

BEKO CWB 9710X Manual

Product: