Manual BEKO BITA 60 I (page 19 of 28) (English, German, Dutch, French, Italian, Portuguese, Spanish)

761497

Zoom out

Zoom in

1/28

- 19 -

product, check that they are suitable for the type of wall on

which the hood is to be fixed.

•Fixingthedecorativetelescopicflue:

- Arrange the electrical power supply within the dimensions

of the decorative flue. If your appliance is to be installed in the

ducting version or in the version with external motor, prepare

the air exhaust opening.

- Adjust the width of the support bracket of the upper flue

(Fig.3).

- Then fix it to the ceiling using the screws A (Fig.3) in such a

way that it is in line with your hood and respecting the distance

from the ceiling indicated in Fig.2.

- Connect the flange C to the air exhaust hole using a

connection pipe (Fig.5).

- Insert the upper flue into the lower flue.

- Fix the lower flue to the hood using the screws B provided

(Fig.5), extract the upper flue up to the bracket and fix it with

the screws B (Fig.3).

- If your appliance has the lower connections indicated as in

Fig.4A, the fixing to be carried out is that shown in Fig.6A.

To transform the hood from a ducting version into a filtering

version, ask your dealer for the charcoal filters and follow the

installation instructions.

•Filterhood:

Please note:

- In order to transform the hood from EXTRACTOR HOOD into

FILTER HOOD the active carbon filters must be ordered at your

distributor as accessory.

We have two different types of Kit, one with non-regenerable

active carbon filters (Fig.7B) and the other one with

regenerable active charcoal filters (washable) (Fig.7C).

- To replace the non-regenerable active carbon filters X, pull

lever outwards as shown in Fig.7B.

USE AND MAINTENANCE

•  We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air. The effective

performance of the cooker hood depends on constant

maintenance; the anti-grease filter and the active carbon filter

both require special attention.

•Theanti-greasefilter is responsible retaining the grease

particles suspended in the air, therefore it is subject to clogging

with variable frequency according to the use of the appliance.

- To prevent the danger of possible fires, at least every 2

months one must wash the anti-grease filters by hand using

non-abrasive neutral liquid detergents or in the dishwasher

at low temperatures and on short cycles.

- After a few washes, colour alterations may occur. This does

not give the right to claim their replacement.

•Theactivecarbonfilters are used to purify the air that is

sent back into the room and its function is to mitigate the

unpleasant odours produced by cooking.

- The non-regenerable active carbon filters must be replaced

at least every 4 months. The saturation of the active charcoal

depends on the more or less prolonged use of the appliance,

on the type of kitchen and on the frequency with which anti-

grease filter is cleaned.

- Regenerable active charcoal filters must be washed by hand,

with non abrasive neutral detergents, or in the dishwasher at

a maximum temperature of 65°C (the washing cycle must be

complete without dishware). Remove excess water without

damaging the filter, remove the plastic parts, and let the

mat dry in the oven for at least 15 minutes approximately at

a maximum temperature of 100°C. To keep the regenerable

charcoal filter functioning efficient this operation must be

repeated every 2 months. These must be replaced at least

every 3 years or when the mat is damaged.

•Beforeremountingtheanti-greasefiltersandthe

regenerable active charcoal filters it is important that they

are completely dry.

•Cleanthehoodfrequently,bothinternallyandexternally,

using a cloth dampened with denatured alcohol or neutral

liquid detergents that are non abrasive.

•  The lighting .system is designed for use during cooking

and not for the prolonged general lighting of the room. The

prolonged use of the lighting system significantly decreases

the average duration of the bulbs.

•  If the appliance is equipped with courtesy lights it is possible

to use them for general room lighting for a prolonged amount

of time.

•Attention: the non compliance with the hood cleaning

warnings and with the replacement and cleaning of the filters

entails risk of fires. One therefore recommends keeping to the

suggested instructions.

•Replacinghalogenlightbulbs(Fig.8):

In order to replace the dichroic lamps, carefully remove

the lamp from the lamp holder with the help of a small flat

screwdriver or a similar tool. PLEASE NOTE! In doing this

operation, please take care not to scratch the hood. Replace

the bulbs with new ones of the same type.

•Replacinghalogenlightbulbs(Fig.9):

To replace the halogen light bulbs B, remove the glass pane

C using a lever action on the relevant cracks. Replace the bulbs

with new ones of the same type. Caution: do not touch the

light bulb with bare hands.

•ReplacingLEDlamps(Fig.10):

If the appliance version is with LED lamps, the intervention of

a specialised technician is necessary to replace them.

•Replacingthehalogen/incandescentlamps(Fig.11):

Only use lamps of the same type and Wattage installed on

the device.

•Commandsluminous (Fig.12.A.B.) the key symbols are

explained below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

F = AUTOMATIC STOP TIMER - 15 minutes (*)

If your appliance has the INTENSIVE speed function, from

speed THREE, press key E for 2 seconds and it will be activated

for 10 minutes after which it will return to the previously

set speed. When the function is active the LED flashes. To

interrupt it before the 10 minutes have elapsed, press key E

again. Some models allow activating this function even with

speed one and two.

By pressing key F for two seconds (with the hood switched off)

the “clean air” function is activated. This function switches the

appliance on for ten minutes every hour at the first speed. As

soon as this function is activated the motor starts up at the

first speed for ten minutes. During this time key F and key

C must flash at the same time. After ten minutes the motor

switches off and the LED of key F remains switched on with

a fixed light until the motor starts up again at the first speed

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of BEKO BITA 60 I in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

BEKO BITA 60 I Manual

Product: