797144
17
Zoom out
Zoom in
Previous page
1/50
Next page
Dishwasher
User’s Manual
EN
15 9140 0100_BEKO_E9_EN/ 06-11-21.(15:57)
DEN48520W
DIN46X30
DEN48X20G
DIN48Q21
BDIN36430
BDIN36520Q
BDIN38640D
BDIN38640C
The following symbols are used in the user manual and on the packaging:
Danger that may result in death or injury.
NOTICE
Danger that may result in damage to the product or its surroundings.
Important information or useful hints about usage.
Read the user manual.
Dear Customer,
Please read this user manual before using the product.
Thank you for choosing this Beko product. We hope that you get the best results
from your product which has been manufactured with high quality and state-of-the-art
technology. Therefore, please read this entire user manual and all other accompanying
documents before using the product.
Follow all warnings and information in the user manual. Thus, you can protect yourself
and your product against potential dangers.
Keep the user manual. If you handover the product to someone else, give the user
manual as well.
This product was manufactured using the latest technology in environmentally friendly conditions.
6/EN
squeezed or crushed while
placing the product into its
location after installation or
cleaning procedures.
Installation Safety
To make the product ready for
use, review the information
in the user manual and
installation instructions and
make sure that the electricity,
water supply and drain
systems are appropriate. If
they are not, call a qualified
technician and plumber
to have the necessary
arrangements carried out.
These procedures are under
customer’s responsibility.
Prior to installation, check
if the product has any
defects on it. If the product
is damaged, do not have it
installed.
Do not install the product
in environments where the
temperature falls below 0ºC.
Do not place the product on
carpets or similar surfaces.
This may cause fire hazard
since the product will not be
ventilated from below.
Place the product on a clean,
flat and solid surface and
balance it with adjustable feet.
If the feet are not adjusted
properly, the door will not
be closed completely and
cause hot steam to escape.
Otherwise, it might cause
serious burns and injuries,
and harm your furniture.
Do not install the product
close to heat sources (heater,
stove and etc.) or under the
cooking area of a hob.
If the product is going to
be used inside a wardrobe/
cabinet/module, keep the
doors of the wardrobe/cabinet/
module open during operation
in cases where there are no
openings to provide sufficient
air circulation.
Plug the product in a
grounded socket protected
by a fuse with current
values as per type label
of the product. Have the
grounding installation made
by a qualified electrician. Do
not use the product without
having the grounding made as
per local/national regulations.
Plug the product in a socket
that conforms the voltage and
frequency values stated on
the type label of the product.
Do not plug the product
in sockets that are loose,
dislocated, broken, dirty,
greasy or bear the risk of
getting in contact with water,
such as places where there
might be water leak from the
counter.
NOTICE
You must use the
new hose set provided with the
product. Do not reuse the old
8/EN
Maintenance and cleaning
safety
Do not wash the product by
spreading or pouring water
onto it.
Do not use sharp or abrasive
tools when cleaning the
product. Do not use home
cleaning products, detergent,
gas, gasoline, thinner, alcohol,
varnish etc.
NOTICE
Do not forget to install
the product’s filter back after
you have cleaned it. Otherwise,
pumps will get clogged and
product will be damaged.
Interior Lighting
Depending on the model
of your product, call the
authorised service agent
when it is required to change
the LED/bulb used for lighting.
Environmental
Instructions
Compliance with WEEE
Directive and Disposing of
the Waste Product
This product complies with
EU WEEE Directive (2012/19/
EU). This product bears a
classification symbol for
waste electrical and electronic
equipment (WEEE).
This symbol indicates
that this product shall
not be disposed with
other household wastes
at the end of its service
life. Used device must
be returned to official collection
point for recycling of electrical
and electronic devices. To find
these collection systems please
contact to your local authorities
or retailer where the product was
purchased. Each household
performs important role in
recovering and recycling of old
appliance. Appropriate disposal
of used appliance helps prevent
potential negative consequences
for the environment and human
health.
2-
10/EN
Technical specifications
Maximum washing capacity (check the
energy label and Programme data and
average consumption values table given
on Quick Guide. )
Height (check installation document for
installation)
Width: 60
Depth: 57
Power input: 220-240 V, 50 Hz *
Total power 1800-2100 W *
Heater power: 1800 W *
Total current: 10 A *
Pump power: 90 - 125 W *
Drain pump power: 30 W *
* For detailed electrical values, check
the type label on the machine door.
Water Pressure 0.3 –10 bar
(= 3 – 100 N/cm² = 0.03-1.0 Mpa)
Technical specifications may be
changed without prior notice to improve
the quality of the product.
Figures in this manual are schematic
and may not match the product exactly.
Values stated on the markings of the
product or in the printed documents
accompanying the product are
obtained in the laboratory on basis of
the relevant standards. These values
may vary according to the usage of the
product and ambient conditions.
Note for test institutions:
Data required for performance tests shall
be provided upon request. Requests can
be e-mailed to the following address:
dishwasher@standardloading.com
Do not forget to provide the code, stock
number and serial number of the product
to be tested in your request e-mail along
with your contact information. Code, stock
number and serial number of the product
may be found on the type label attached to
the side wall of the door.
Compliance to standards and test
data/EC declaration of conformity
Development, production and
sales stages of this product comply
with the safety rules included in all
pertaining European Community
regulations.
2014/35/EU, 2014/30/EU, 93/68/EC, IEC
60436 / EN 60436
The model information as stored in
the product database can be reached
by entering following website and
searching your model identifier (*)
found on energy label.
https://eprel.ec.europa.eu/
XXXXXXXXXX (*)
18 7575 8000
3:25
REV:AA
12.9 L
94
13 x
kWh
2019/2017
48
db
11/EN
Your dishwasher
Overview
1. Upper basket
2. Upper impeller
3. Lower impeller
4. Cutlery basket (depends on model)
5. Door
6. Rating Label
7. Control panel
8. Detergent dispenser
9. Lower basket
10. Filters
11. Salt reservoir lid
12. Upper basket rail
13. Upper cutlery basket (depends on model)
14. Tabletop (depends on model)
15. Fan drying system (depends on model)
15
3-
15
12/EN
Installation
Read “Safety Instructions” section first!
Installation procedures must always be
performed by the manufacturer, authorised
service agent or a qualified person
specified by the importer. To make the
product ready for use, make sure that
the electricity, tap water supply and water
drainage systems are appropriate before
calling the authorised service agent. If
they are not, call a qualified technician
and plumber to have the necessary
arrangements carried out.
Preparation of the location and
electrical, tap water and waste water
installations at the place of installation
is under customer's responsibility.
Installation and electrical connections
must be carried out by the authorised
service agent. Manufacturer shall
not be held responsible for damages
arising from processes carried out by
unauthorised persons.
Prior to installation, check if the product
has any defects on it. If the product
is damaged, do not have it installed.
Damaged products cause risks for your
safety.
Make sure that the water inlet and
discharge hoses are not folded,
pinched or crushed while pushing the
product into its place after installation
or cleaning procedures.
The front of the appliance may not be
removed on free-standing or under-the-
counter models. The warranty will be
void if this is done.
When placing the product, pay attention not
to damage the floor, walls, piping, etc. Do
not hold the product from its door or panel
to move it.
Appropriate installation location
In the area where this product is
installed, there must not be a lockable,
sliding or hinged door that will restrict
full opening of the product’s door.
Make sure that you select a location
that will allow you to load and unload
the dishes in a fast and comfortable
manner.
Place the product on a solid and flat
floor that has sufficient load carrying
capacity! The product must be installed
on a flat surface in order for the door to
be closed properly and securely.
Do not install the product at places
where temperature may fall below 0ºC.
Place the product on a hard floor. Do
not place it on a long pile rug or similar
surfaces.
Do not place the product on the power
cable.
Make sure that you select a location
that will allow you to load and unload
the dishes in a fast and comfortable
manner.
Install the product at a place close to
the tap and the drain hole. Select the
installation location by considering
that it will not be changed after the
connections are made.
Connecting water supply
We recommend installing a filter at
the water inlet in order to prevent the
dirt (sand, clay, rust) in the mains or
water installation of your home from
damaging the machine or the dishes.
4-
13/EN
Permitted water temperature: up to
25°C ( 60°C for products equipped
with Aquasafe+; please refer to
Aquasafe+ section )
The dishwasher may not be connected to
open warm water devices or flow-through
water heaters.
NOTICE
Do not use an old or used water
inlet hose on the new product. Use the new
water inlet hose supplied with the product.
Do not make extension at the hoses.
NOTICE
Connect the water inlet hose
directly to the water tap. Pressure coming
from the tap should be 0.3 bars minimum
and 10 bars maximum. If the water
pressure exceeds 10 bars, a pressure relief
valve should be installed in between.
NOTICE
The water supply and draining
hoses must be securely fastened and
remain undamaged.
NOTICE
Open the taps completely after
making the connections to check for water
leaks.
Aquasafe+
(depends on the model)
The Aquasafe+ system protects against
water leaks that may occur at the hose
inlet.Water contact with the valve box of
the system must be avoided to prevent
damage to the electrical system.
As the hose set contains electrical
connections and assemblies, never
shorten or lengthen the hose with
extension hoses.
If the Aquasafe+ system is damaged,
unplug the product and call the
authorised service agent.
14/EN
Drain pipe must be connected to the
sewage system and it should not be
connected to any surface water.
Adjusting the feet
If the door of the product cannot be closed
properly or if the product rocks when you
push it slightly, then you need to adjust
the feet of the product. Adjust the feet of
the product as illustrated in the installation
manual supplied with the product.
Steam may escape if the door of the
dishwasher is not adjusted properly.
Hot steam may cause serious burns
and injuries and damage your furniture.
Connection to the drain
Water discharge hose can directly be
connected to the drain hole or sink’s
drainage. See the installation manual
supplied with your machine for detailed
information.
min
300
min
120
max 1000
min 500
Electrical connection
Connect the product to a grounded
outlet protected by a fuse complying
with the values in the "Technical
specifications" table. Our company
shall not be liable for any damages
that will arise when the product is used
without grounding in accordance with
the local regulations.
Connection must comply with national
regulations.
Power cable plug must be easily
accessible after installation.
Plug in the product to a grounded
socket which is protected by a fuse of
10 Amperes.
The specified voltage must be equal to
your mains voltage.
Do not make connections via extension
cables or multi-plugs.
Damaged power cables must be
replaced by the authorised service
agent.
This appliance must be earthed. If the
fitted moulded plug is not suitable for
your socket, then the plug should be
cut off and an appropriate plug fitted.
Destroy the old plug, which is cut off as
a plug with a bared cord could cause a
shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance
incorporates a 13A fuse. Should the
fuse need to be replaced an ASTA
approved BS1362 fuse of the same
rating must be used. Do not forget
to refit the fuse cover. In the event of
losing the fuse cover, the plug must
not be used until a replacement fuse
cover has been fitted. Colour of the
replacement fuse cover must be the
same colour as that visible on the
15/EN
pin face of the plug. Fuse covers are
available from any good electrical
store.
Fitting a different plug
As the colours of the wires in the mains
lead of this appliance may not correspond
with the coloured markings identifying the
terminals on your plug, proceed as follows:
1. Connect the green - yellow or green
(earth) wire to the terminal in the plug
marked ‘E’ or with the symbol or
coloured green and yellow or green.
2. Connect the blue (neutral) wire to
the terminal in the plug marked ‘N’ or
coloured black.
3. Connect the brown (live) wire to the
terminal in the plug marked ‘L’ or
coloured red.





With the alternative plugs a 13A fuse must
be fitted either in the plug or adaptor or
in the main fuse box. If in doubt contact a
qualified electrician.
17/EN
You can put about 2 kg of softening
salt into the salt reservoir.
5. Replace the lid and tighten it when the
reservoir is full.
You need to add salt right before
starting the machine. Thus, the
overflowing salty water will be flushed
immediately, preventing the risk
of corrosion in machine. In cases
where you would not start washing
immediately, run your machine empty
in the shortest programme.
Since different salt brands in the
market have different particle sizes and
since the water hardness may vary,
dissolution of the salt in water may
take a couple of hours. Therefore, Salt
Indicator remains on for a while after
adding salt into the machine.
Detergent
You can use powder, liquid/gel or tablet
detergents in the machine.
Only use detergents produced
particularly for use with dishwashers.
Note that detergents that contain
chlorine and phosphate can be harmful
for the environment. Liquid detergents
without chlorine may not remove tea
and coffee stains from cups.
Adding detergent
Pay attention to the warnings on the
detergent packaging to get better
washing and drying results. Contact
Adding salt
Water softening system needs to be
regenerated in order for the product
to operate with the same performance
continuously. Dishwasher salt is used for
this purpose.
Use only special softening salts
produced particularly for the
dishwashers in your machine.
It is recommended to use granule- or
powder-formed softening salts in the
water softening system. Do not use
salts that do not completely dissolve
in water such as table salt or rock
salt. Otherwise the performance of the
system may deteriorate in time.
Salt reservoir will be filled with water
when you start the product. For this
reason, add salt before operating the
machine.
1. Firstly, take the lower basket out to add
softening salt.
2. Turn the salt reservoir lid counter-
clockwise to open it (A).
3. Add 1 liter of water to salt reservoir of
your machine only in initial use.
4. Fill the salt reservoir with salt by
using the salt funnel (D). To speed up
dissolution rate of salt in water, stir it
with a spoon.
19/EN
3. After the empty washing cycle, review
the user manual and readjust the water
hardness level so as to suit the water
supply.
4. Make the appropriate rinse aid settings.
Rinse aid
The rinse aid used in dishwashers
is a special combination that aims to
increase drying efficiency and prevent
water or lime stains on the washed
items. For this reason, care must be
paid to have rinse aid in the rinse
aid reservoir and to use rinse aids
produced specially for dishwashers
only.
1. Open the lid of the rinse aid reservoir
with the help of the latch.
2. Fill the reservoir until “MAX” level.
Tablet detergents
In addition to the conventional tablet
detergents, there are also commercially
available detergent tablets that show water
softening salt and/or rinse aid effect. Some
types of these detergents contain special-
purpose components such as glass and
stainless steel protectors. These tablets
show their effects up to a certain water
hardness level (21°dH). Water softening
salt and rinse aid must also be used
together with the detergent if the water
hardness level is above the mentioned
level.
The best washing performance in
dishwashers is obtained by using
detergent, rinse aid and water
softening salt individually.
Observe the instructions of the
detergent manufacturer on the package
when using tablet detergents.
Contact the detergent manufacturer if
your dishes are wet and/or if you notice
limescale spots particularly on your
glasses after the washing programme
is over when using a tablet detergent.
When you switch to powder
detergent from tablet detergent:
1. Make sure that salt and rinse aid
reservoirs are full.
2. Set the water hardness to the highest
level and perform an empty run.
20/EN
3. Slightly press the point (B) of the
reservoir lid to close it.
4. If there are stains on tableware items
after washing, level must be increased
and if there is a blue trace after wiping
them by hand, it must be decreased.
This is set to position 3 as factory
default.
The rinse aid adjustment is described
under "Adjusting the amount of rinse
aid" in the section for operating the
machine.
Wipe clean any spilled rinse aid
outside the reservoir. Rinse aid that
spilled accidentally will cause foaming
and it will eventually decrease washing
performance.
Items not suitable for washing in
the dishwasher
Never wash dishes soiled by cigarette
ash, candle remnants, polish, dyestuff,
chemicals, etc. in your dishwasher.
Do not wash silverware and cutlery
with wooden or bone stems, glued
pieces, or pieces that are not resistant
to heat, as well as copper and tin-
plated containers in the dishwasher.
Decorative prints of chinaware as well
as aluminium and silver items may get
discoloured or tarnished after washing
in the dishwasher just as it happens in
handwashing as well. Some delicate
glass types and crystals may become
dull in time. We strongly recommend
you to check if the tableware you
are going to purchase is suitable for
washing especially in the dishwasher.
Placing the dishes into the
dishwasher
Depending on the capacity of your
dishwasher, you can use your dishwasher
in the optimum way with respect to energy
consumption and washing and drying
performance only if you place the dishes in
an orderly way.
Wipe away any coarse food remnants
(bones, seeds, etc.) on the dishes
before placing them in the dishwasher.
Place thin, narrow pieces in the middle
sections of baskets if possible.
Place the heavily soiled and bigger
items in the lower basket and smaller,
delicate and light items in the upper
basket.
Place the hollowed dishes such as
bowls, glasses and pans upside down
in the dishwasher. Thus, accumulation
of water in deep hollows is prevented.
To prevent possible injuries, always
place the sharp and pointed dishes
such as service fork, bread knife, etc.
upside down so as their pointed ends
will face down or lay them horizontally
in the dish basket.
Unload dishes in the lower basket first and
then the dishes in the upper basket.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO BDIN38640C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO BDIN38640C in the language / languages: English as an attachment in your email.

The manual is 14.29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BEKO BDIN38640C

BEKO BDIN38640C User Manual - German - 51 pages

BEKO BDIN38640C User Manual - Dutch - 48 pages

BEKO BDIN38640C User Manual - French - 51 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info