Manual BEKO BCL 90X (page 21 of 32) (English, German, Dutch, French, Italian, Portuguese, Spanish)

676635

Zoom out

Zoom in

1/32

over the hood, remove the metal blank with a screwdriver or

other suitable tool, and tighten the engine group by using

the screws provided (Fig.1B).

- Make the hole in the ceiling to accommodate the device

taking into account the dimensions shown in Figure 2.

ATTENTION: Make sure that the ceiling structure supports

theunit'sweight.Ifnot,prepareasuitableframetofull

such function.

- Tighten the power box over the upper part of the hood using

the screws provided (Fig.5).

- With a tting pipe, connect the ange (Fig.1C) to the air

extraction hole.

- Take the unit and place it inside the hole, just as you did in

the ceiling. Make sure that the brackets are perfectly hooked

(Fig.6A).

- Tighten the brackets by using the screws inside the hood, as

shown in Figures 6B and 6C.

- If necessary, there is also the possibility of xing the device

with additional screws from inside the hood to an undercoun-

ter light (if present) (Fig.2A).

- Open the panel by pressing the point indicated in Fig.7.

- For dierent types of assemblies, use screws and anchors

that are suitable for the wall material (e.g.: reinforced concrete,

plasterboard, etc). If the screws and anchors are provided with

the product, make sure that they are suitable for the type of

wall to which the hood is xed.

USE AND MAINTENANCE

•  We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The eective performance of the cooker hood depends on

constant maintenance; the anti-grease lter and the active

carbon lter both require special attention.

•Theanti-greaselter is responsible retaining the grease

particles suspended in the air, therefore it is subject to

clogging with variable frequency according to the use of the

appliance.

- To prevent the danger of possible res, at least every 2

months one must wash the anti-grease lters by hand using

non-abrasive neutral liquid detergents or in the dishwasher

at low temperatures and on short cycles.

- After a few washes, colour alterations may occur. This does

not give the right to claim their replacement.

•Beforeremountingtheanti-greaseltersandtherege-

nerableactivecharcoalltersitisimportantthattheyare

completely dry.

•  Clean the hood frequently, both internally and externally,

using a cloth dampened with denatured alcohol or neutral

liquid detergents that are non abrasive.

•  The lighting .system is designed for use during cooking

and not for the prolonged general lighting of the room. The

prolonged use of the lighting system signicantly decreases

the average duration of the bulbs.

•  If the appliance is equipped with courtesy lights it is possible

to use them for general room lighting for a prolonged amount

of time.

•Attention: the non compliance with the hood cleaning

warnings and with the replacement and cleaning of the lters

entails risk of res. One therefore recommends keeping to the

suggested instructions.

•Replacinghalogenlightbulbs(Fig.10):

To replace the halogen lamps, B push the watch glass C and

open the flap.

Replace them with a light of the same type.

Attention: do not touch the lights with your hands.

If the appliance version includes LED lamps, the intervention

of a specialised technician is necessary to replace them.

•Commands(Fig.11):

NOTE: all units’ functions are controlled through a remote

control.

If the remote control stops functioning (because of low bat-

teries, etc.) you can directly use the control inside the unit

(Fig.9-11).

PowerButton(A)= The on/off button switches on and off

the whole hood (motor and lights).

By pressing the button the motor starts at 1st speed.

FanSpeedbutton(B)= From the OFF position, press once

for the 1st speed, twice for the 2nd speed and three times for

the 3rd speed. In order to activate the intensive speed, press

the button for 5 seconds regardless of the status of the hood.

For each speed only the led indicating the set speed will turn

on. The intensive speed is indicated by the flashing of the

led indicating speed 3. The duration of the intensive speed

is 10 minutes; after this time the hood goes back to the last

set speed. In order to remove the intensive speed press the

power button and the hood will switch off, or press the Fan

speed button and the speed goes back to the previously set

one. Speed of the hood with cyclic trend.

Lightbutton(C)= There are three light levels: High, medium,

low. From the off position press once for the high level, twice

for the medium level, three times for the low level and four

times to turn the lights off. The level of the lights has a cyclic

trend: High, medium, low, off.

Timerbutton(D)= With any type of speed (excluding the

intensive speed), by pressing the button, the timer function is

activated for 15 minutes. After this time has elapsed the hood

will turn off (motor and any light on).

Lightsindicator(E)= The lights indicator will switch on when

the lights are on at any level.

Filtersindicator(F)= After 30 minutes of operation, the led of

the filters indicator will switch on, not flashing indicating that

the anti-grease filters have to be washed. To reset the function

(with the hood off), press the Fan speed button for 5 seconds.

After this operation, the led of the filters indicator turns off and

the setting of the 30 hours starts again from the beginning.

Cleanairindicator(G)=With the hood off, press the Power

button (A) for 5 seconds to activate the clean air function. This

will switch on the motor at speed 1 for 10 minutes every hour.

The light indicator will switch on without flashing and the led

of the 1st speed will switch on. In the remaining 50 minutes

the light indicator will flash. The function can be deactivated

by pressing any button except for the lights one.

•Commands(Fig.12):

Lightbutton(1):

- Lights are three level (high, medium, low).

- From off, touch once for high.

- From off, touch twice for medium.

- From off, touch three times for low.

- From off, touch four times to cycle back to off.

- Light level will cycle from high, medium, low, off.

Powerbutton(2):

- Power Button will turn power on and off for the entire hood

(fan and lights).

- Hood will remember the last speed and light level it was last

turned off at (Example: hood is turned off at when it was last

on high speed and high lights; hood will turn back on at high

speed and high lights when Power Button is pressed).

- 21 -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of BEKO BCL 90X in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

BEKO BCL 90X Manual

Product: