817023
10
Zoom out
Zoom in
Previous page
1/48
Next page
10 / EN
Washing Machine / User Manual
4.1 Installation
APlease read the “Safety Instructions” section first!
Apply to the nearest authorized service agent for the installation of your product.
Preparation of the location and electrical, tap water and waste water installations at the place of installation
is under customer's responsibility.
Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or
crushed while pushing the product into its place after installation or cleaning procedures.
Make sure that the installation and electrical connections of the product are performed by authorized
service agent. Manufacturer shall not be held responsible for damages caused by operations performed by
unauthorized persons.
Prior to installation, visually check if the product has any defects on it. Do not have it installed if the
appliance is damaged. Damaged products cause risks for your safety.
4.1.1 Appropriate installation location
Place the product on a solid and level floor. Do not place it onto a carpet with high pile or other similar
surfaces. Inappropriate floor may cause problems of noise and vibration.
Total weight of the washing machine and the dryer -with full load- when they are placed on top of each
other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load
carrying capacity!
Do not place the product on the power cable.
Do not install the product at places where temperature may fall below 0ºC. Freezing might damage your
product.
Leave a minimum space of 1 cm between the product and the furniture.
If you will install the product on a surface with steps, never place it close to the edge.
Do not place the product on any platform.
Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use them
on the product.
4.1.3 Removing transportation safety bolts
1 Loosen all transportation safety bolts with an appropriate wrench until they turn freely.
2 Stretch the internal component by pressing on the holding areas and pull the component out.
3 Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel.
WARNING Remove the transportation safety bolts before operating the product! Otherwise, the product will get damaged.
WARNING
Keep the transportation safety bolts in a safe place to reuse when the product needs to be moved again in the future.
Install the transportation safety bolts in reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO B5W5841A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO B5W5841A in the language / languages: English as an attachment in your email.

The manual is 3.95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info