817027
46
Zoom out
Zoom in
Previous page
1/56
Next page
EN / 46
Water inside the product.
Some water has remained in the product
due to the quality control processes in the
production. >>> This is not a failure; water
is not harmful to the product.
The product does not take water in.
Tap is turned off. >>> Turn on the taps.
Water inlet hose is bent. >>> Flatten the
hose.
Water inlet filter is clogged. >>> Clean the
filter.
Loading door is not closed. >>> Close the
door.
The product does not drain water.
Water drain hose is clogged or twisted.
>>> Clean or flatten the hose.
Pump filter is clogged. >>> Clean the
pump filter.
Product vibrates or makes noise.
Product is standing unbalanced. >>> Ad-
just the stands to balance the product.
A hard substance has entered into the
pump filter. >>> Clean the pump filter.
Transportation safety bolts are not re-
moved. >>> Remove the transportation
safety bolts.
Laundry quantity in the product is too little.
>>> Add more laundry to the product.
Excessive laundry is loaded in the product.
>>> Take out some of the laundry from
the product or distribute the load by hand
to balance it homogeneously in the
product.
Product is leaning on a rigid item. >>>
Make sure that the product is not leaning
on anything.
There is water leaking from the bottom
of the product.
Water drain hose is clogged or twisted.
>>> Clean or flatten the hose.
Pump filter is clogged. >>> Clean the
pump filter.
Product stopped shortly after the pro-
gramme started.
Machine has stopped temporarily due to
low voltage. >>> Product will resume run-
ning when the voltage restores to the nor-
mal level.
Product directly drains the water it
takes in.
Draining hose is not at adequate height.
>>> Connect the water draining hose as
described in the user manual.
No water can be seen in the product
during washing.
Water is inside the invisible part of the
product. >>> This is not a failure.
Loading door cannot be opened.
Loading door lock is activated because of
the water level in the product. >>> Drain
the water by running the Pump or Spin
programme.
Product is heating up the water or it is at
the spinning cycle. >>> Wait until the pro-
gramme completes.
Loading door may be stuck because of
the pressure it is subjected to. >>> Grab
the handle and push and pull the loading
door to release and open it.
If there is no power, loading door of the
product will not open. >>> To open the
loading door, open the pump filter cap and
pull down the emergency handle posi-
tioned at the rear side of the said cap. See
Loading Door Lock [}37]
Washing takes longer than specified in
the user manual. (*)
Water pressure is low. >>> Product waits
until taking in adequate amount of water to
prevent poor washing quality due to the
decreased amount of water. Therefore, the
washing time extends.
Voltage is low. >>> Washing time is pro-
longed to avoid poor washing results
when the supply voltage is low.
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO B3D59644U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO B3D59644U in the language / languages: English as an attachment in your email.

The manual is 1.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info