660519
14
Zoom out
Zoom in
Previous page
1/22
Next page
14 XENYX XL3200/XL2400/XL1600 User Manual
5.5 Subgroups
The XENYX provides 4 subgroups which allow you to feed multiple channels
to mono or stereo mixdowns. Their volume level can be adjusted using the
subgroup faders. For example, createa subgroup with all vocal channels or drum
signals and adjust the volume using the subgroup fader. This way you can keep
track and, at the same time, can process the signal with a compressor via the
subgroup insert.
Additionally, you can also use the subgroup outputs as sends for a
multitrackrecorder.
PAN
The PAN control adjusts the position within the stereo image.
MAIN
The MAIN switch routes the subgroup signal to the main mix.
With the PAN control you can adjust the signal to the left side of the stereo
image (PAN turned fully left), to the right side of the stereo image (PAN turned
fully right) or to both sides (PAN in center position) of the stereo main mix.
Forexample, when creating a stereo submix with the subgroups 1 and 2, group1
should be adjusted to the left and group 2 to the right side of the main mix in
order to maintain a balanced stereo image. In case you have created a mono
submix with only one subgroup, be sure to center the PAN control so that the
signal is not only heard on one side.
SOLO
The SOLO switch routes the subgroup signal to the AFL bus (Solo In Place) orPFL
bus (Pre Fader Listen), so that you can monitor the subgroup signal without
aecting the main or sub output signals. The signal to be monitored is taken
either pre (PFL, mono) or post-subgroup fader (Solo, stereo), depending on the
position of the SOLO/PFL switch. The SOLO LED illuminates when the SOLO switch
is pressed.
CLIP
The CLIP LED lights up as soon as the subgroup signal's level is too high.
Inthiscase, pull down the channels' faders routed to this group.
SIG
The SIG LED lights up when a signal is routed to the subgroup whose level is
higher than -20 dB.
The signal and clip LEDs are not affected by the fader. The signals are
indicated even when the subgroup fader is pulled down.
Fader
The subgroup faders adjust the volume level of the subgroup signal at the
subgroup output. If the MAIN switch is pressed, you can also adjust the
subgroup's volume level in the main mix.
5.6 Further functions of the mastersection
5.6.1 Talkback
The talkback function of the XENYX allows you to communicate with people on
stage. The talkback signal can be routed to the dierent bus outputs.
MIC
Here you can plug in the microphone for talkback use.
LEVEL
The LEVEL control adjusts the volume level of the talkbacksignal.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx XL2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx XL2400 in the language / languages: English as an attachment in your email.

The manual is 6,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx XL2400

Behringer Xenyx XL2400 Quick start guide - English, German - 18 pages

Behringer Xenyx XL2400 User Manual - German - 21 pages

Behringer Xenyx XL2400 User Manual - Dutch - 21 pages

Behringer Xenyx XL2400 Quick start guide - French, Portuguese, Spanish - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info