660519
10
Zoom out
Zoom in
Previous page
1/22
Next page
10 XENYX XL3200/XL2400/XL1600 User Manual
4.7 FX/Mon/Aux sends
FX 1 and 2
The FX outputs 1 and 2 provide the signals of the eects buses 1 and 2.
Thesesignals may be sent to external eects processors and are routed back over
the AUX-RETURN inputs or separate input channels, for example.
MON 1 and 2
The monitor outputs 1 and 2 provide the signals of the monitor buses.
Thesesignals may be be sent to stage loudspeakers. To prevent interference due
to the long cables being used between stage and mixing console, the outputs
are balanced XLR connectors. What's more, youhave the right connectors when
working with multicores.
AUX 1 and 2
The AUX outputs 1 and 2 provide the signals of the AUX buses 1 and 2.
Youcanswitch these buses pre-fader and post-fader so that they may be
usedforeects as well as for monitor applications.
4.8 Aux returns
AUX RETURN
The stereo AUX inputs 1 und 2 let you connect the mixer to additional equipment
(players,eectsprocessors, submixers, etc.). Thesignal is sent to the signal sum.
FX RETURN
The stereo FX RETURN connectors 1 and 2 are linked to the outputs of external
eects processors. Depending on the routing, the signals are sent to the
subgroup or the main mix bus.
4.9 Light and headphone connectors
LAMPS
The LAMPS plugs are for connecting gooseneck lamps with BNC connectors.
Thepower supply is 12 V _ and the total connection load is 5 Watts a lamp.
PHONES
The PHONES outputs (¼" stereo jacks) let you plug in your headphones.
5. Control Elements
This chapter describes the various control elements of your mixing console.
Eachcontrol and switch is explained in full detail.
5.1 Mono channels
+48 V
This control LED lights up as long as the phantom power is switched on.
Theswitch is found on the rear panel of the unit.
Trim
The TRIM control adjusts the input gain.
Be sure to set this control fully counter-clockwise before you connect or
disconnect a signal source to or from one of the inputs.
The dial oers 2 dierent value ranges. The rst value range between 0 and +60
refers to the microphone input, indicatingthe degree of amplication applied to
the input's signal. Thesecond value range between -20 and +40 dB refers to the
amplication of the line input. When centered (at12o'clock), the line signals are
neither boosted nor cut.
80 Hz
Press the 80 Hz switch to activate the high-pass lter which blends out
low-frequency noise (-3 dB at 80 Hz, 18 dB/octave).
Equalization
The mono input channels provide 4-band equalization with 2semi-parametric
mids. You can boost or cut the bands up to 15 dB. When in center position (0 dB),
the equalizer has a atresponse.
HIGH
The high-frequency range is processed with a shelving lter above 12 kHz.
HIGH MID
A semi-parametric peak lter processes the upper mid range between 400 Hz
and 8 kHz. The FRE control selects the frequency which is boosted or cut by using
the HIGH MID control.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx XL2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx XL2400 in the language / languages: English as an attachment in your email.

The manual is 6,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx XL2400

Behringer Xenyx XL2400 Quick start guide - English, German - 18 pages

Behringer Xenyx XL2400 User Manual - German - 21 pages

Behringer Xenyx XL2400 User Manual - Dutch - 21 pages

Behringer Xenyx XL2400 Quick start guide - French, Portuguese, Spanish - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info