660520
8
Zoom out
Zoom in
Previous page
1/22
Next page
8 XENYX XL3200/XL2400/XL1600 User Manual
4. Connectors
Let's begin with the rear panel where the majority of inputs and outputs
arelocated.
4.1 Power supply
IEC receptacle
The mains connection is a standard IEC receptacle. Anappropriate power cord is
supplied with the unit.
FUSE HOLDER
Before connecting the unit to the mains, ensure that the voltage setting matches
your local voltage. Blown fuses should only be replaced by fuses of the same type
and rating. Please also read the information given in chapter “Specications.”
POWER
Use the POWER switch to turn on the mixing console. The POWER switch
should always be in the “O” position when you are about to connect your
unitto the mains.
To disconnect the unit from the mains, pull out the main cord plug.
Wheninstalling the product, ensure that the plug is easily accessible.
Ifmountingin a rack (XL1600 only), ensure that the mains can be easily
disconnected by a plug pull or by an all-pole disconnect switch on or near
therack.
Please note: The POWER switch does not fully disconnect the unit from
the mains. To disconnect the unit from the mains, pull out the main
cord plug or appliance coupler. When installing the product, ensure the
plug or appliance coupler is readily operable. Unplug the power cord
when the unit is not used for prolonged periods of time.
SERIAL NUMBER
This is the serial number of the mixing console.
4.2 Mono inputs
MIC
The balanced XLR input connects to microphones, DIboxesand multicores.
(Multicores are cables that have multiple cores and which run from the so-called
stagebox to the mixer.)
Connect the microphone and mute all mixer outputs before turning on
the phantom power to avoid noise when the microphone is turned on.
Please wait for about one minute when switching on the mic until the
voltage is stable. Only then turn on the input amplification.
Caution! Never use unbalanced XLR connectors (pins 1 and
3 interconnected) on the MIC input jacks, if you want to use
phantom power.
+48 V
Phantom power is used for operating a capacitor microphone. A control
LED lights up next to the switch when the phantom power supply is active.
Additionalcontrol LEDs are located in each Trim section of the mixer's
channels. As a rule, dynamic microphones can still be used with phantom
power, providedthey are wired in a balanced conguration. In case of doubt,
contactthemicrophone manufacturer!
LINE
This is a ¼" jack connector which connects to line-level signal sources
(forexample, keyboards, CD players and wireless microphone receivers).
The input is balanced (TRS connector) but can also be used with unbalanced
connectors (TS connector).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx XL1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx XL1600 in the language / languages: English as an attachment in your email.

The manual is 6,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx XL1600

Behringer Xenyx XL1600 Quick start guide - English, German - 18 pages

Behringer Xenyx XL1600 User Manual - German - 21 pages

Behringer Xenyx XL1600 User Manual - Dutch - 21 pages

Behringer Xenyx XL1600 Quick start guide - French, Portuguese, Spanish - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info