660463

Behringer Xenyx QX1202USB Manual

7
Zoom out
Zoom in
Previous page
1/15
Next page
7 XENYX QX1202USB/QX1002USB User Manual
BAL
The BAL(ANCE) control determines the levels of left and right input signals
relative to each other before both signals are then routed to the main stereo mix
bus. If a channel is operated in mono via the left line input, thiscontrol has the
same function as the PAN control used in the mono channels.
LEVEL
The LEVEL control determines the volume of the channel being sent to the
mainmix.
+4/-10
The stereo inputs of the XENYX have an input sensitivity switch which selects
between +4 dBu and -10 dBV. At -10dBV (home-recording level), the input is
more sensitive (requires less level to drive it) than at +4 dBu (studio level).
2.3 Connector array of the main section
Fig. 2.3: Connectors of the main section
FX SEND
The FX SEND connector outputs the signal you picked up from the individual
channels using the FX controls. You can connect this to the input of an external
eects device in order to process the FX bus’ master signal. Once an eects mix is
created, the processed signal can then be routed from the eects device outputs
back into a stereo input.
◊ If the connected effects processor receives no input signal,
the FX SEND control is probably too low. This also goes for the built-in
effects processor.
◊ Adjust your external effects processor to 100% wet (effects signal
only), because the effects signal is added to the main mix along with
the “dry” channel signals.
◊ In this instance, the FX control of the channel being used as an effects
return should be turned fully counterclockwise, otherwise feedback
problems can occur!
PHONES/CTRL ROOM OUT
The stereo PHONES connector (at the top of the connector panel) is where
h
eadphones are connected. The balanced CTRL ROOM OUT connectors carry
the summed effects and main mix signals. ThePHONES/CONTROL ROOM
control in the main section adjusts the level of both headphones and main
monitoroutputs.
MAIN OUT
The MAIN OUT connectors are balanced mono connectors. The main mix signal
appears here at a level of 0 dBu. The MAIN MIX fader adjusts the volume of
theseoutputs.
2-TRACK INPUT
The 2-TRACK INPUTs are used to bring an external signal source (e.g. CD player,
tape deck, etc.) into the console. They can also be used as a standard stereo line
input, so the output of a second XENYX or BEHRINGER ULTRALINK PRO MX882 can
be connected. Alternatively the line or tape output of a hi- amplier with source
selection switch could also be hooked up here, allowing you to easily listen to
additional sources (e.g. CD player, MP3 player, sound card etc.).
2-TRACK OUTPUT
These connections are laid out as RCA connectors and are wired parallel to
MAINOUT. Connect the inputs of a computer sound card or a recorder here.
Theoutput signal level is set up using the highly accurate MAIN MIX fader.
2.4 Main section
CLIP
SIG
Fig. 2.4: Control elements of the main section
+48 V
The red “+48 V” LED lights up when the phantom power is turned on.
Phantompower is required to operate condenser microphones and is activated
using the +48 V switch located above the +48VLED.
◊ Connect microphones before you switch on the phantom power supply.
Please do not connect microphones to the mixer (or the stagebox/
wallbox) while the phantom power supply is switched on. In addition,
the monitor/PA loud speakers should be muted before you activate the
phantom power supply. After switching on, wait approx. one minute to
allow for system stabilization.
◊ Caution! You must never use unbalanced XLR connectors
(PIN 1 and 3 connected) on the MIC input connectors if you want to
use the phantom power supply.
POWER
The POWER LED indicates that the console is powered on.
LEVEL INDICATOR
The 4-segment display accurately displays the relevant signal level.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx QX1202USB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx QX1202USB in the language / languages: English as an attachment in your email.

The manual is 2,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx QX1202USB

Behringer Xenyx QX1202USB Quick start guide - English, German, French, Portuguese, Spanish - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info