660464
8
Zoom out
Zoom in
Previous page
1/15
Next page
8 XENYX QX1202USB/QX1002USB User Manual
LEVEL SETTING:
To correctly set the gains of the channels, rst set the LEVEL controls of the input
channels to their center positions. Then use the GAIN controls to increase the
input amplication until signal peaks show 0 dB on the level meter.
When recording to digital recorders, the recorders peak meter should not go into
overload. While analog recorders can be overloaded to some extent, creating only
a certain amount of distortion, digital recorders distort quickly when overloaded.
In addition, digital distortion is not only undesirable, but also renders your
recording completely useless.
The CLIP-LED’s of your XENYX display the level virtually independent
of frequency. A recording level of 0 dB is recommended for all
signal types.
MAIN MIX
Use the MAINMIX fader to adjust the volume of the main out.
PHONES/CONTROL ROOM
Use the PHONES/CONTROL ROOM control to adjust the signal level of the
CONTROLROOM and PHONES outputs.
USB/2TR TO MAIN MIX
When the USB/2TR TO MAIN MIX switch is pressed, the 2-Track and USB
inputs are assigned to the main mix, providing an additional input for MP3
players, computers, MIDI instruments or other signal sources that do not require
any processing. Pressing this button automatically mutes the 2-TR OUT/USB
recordingsignal.
USB/2TR TO PHONES/CTRL RM
Press the USB/2TR TO PHONES/CTRL RM switch if you want to monitor the
2-Track and USB inputs via the CTRL ROOM and PHONES outputs. A typical studio
application of this function is recording music into a digital audio workstation
(DAW) with simultaneous reproduction (see ch. 3.1).
FX TO CONTROL
If you want to monitor only the eects signal in your headphones or monitor
speaker(s), press the FX TO CTRL RM switch. Now the signal of the eects
processor can be monitored alone, and the main mix and/or 2-Track signal is no
longer present on the phone and control room outputs.
2.5 USB Connector
Fig 2.5: USB connector
USB CONNECTOR
Connect your mixer to a computer using a standard USB cable. This enables a
stereo signal to be sent to and from your mixer and computer. The signal sent
from the mixer to the computer is the same as the main bus. The audio returning
from the computer into the mixer appears directly in the main and/or control
room bus (depending on USB/2TR to MAIN and PHONES/CTRL RM buttons).
Insert the USB type B plug into the USB jack on the mixer, and the other end
into a free USB port on your computer. There are no required drivers, but we
recommend that PC users install the ASIO driver which can be downloaded from
behringer.com.
NOTE: The mixer cannot be bus-powered via USB! Always use the included power
adaptor to supply power to the mixer.
2.6 Digital eects processor
CLIP
SIG
Fig. 2.6: Eects section
100 KLARK TEKNIK EFFECTS
The XENYX QX1202USB/QX1002USB features a built-in digital stereo eects
processor designed by KLARK TEKNIK. Thiseects processor oers a large
number of standard eects such as Hall, Chorus, Flanger, Delay and various
combination eects. Using the FX control, youcan feed signals into the eects
processor. Theintegrated eects module has the advantage of requiring no
wiring. Thisway, the danger of creating ground loops or uneven signal levels is
eliminated at the outset, completely simplifying the handling.
SIGNAL and CLIP LED
The SIGNAL LED on the eects module shows the presence of a signal whose
level is high enough. This LED should always be on. However, make sure that the
CLIP LED lights up only sporadically. If it is lit constantly, you are overdriving the
eects processor, which leads to unpleasant distortion. If this occurs, turn the
FXcontrols down somewhat.
PROGRAM
The PROGRAM control has two functions: by turning the PROGRAM control,
you dial the number of an eect. The number of the preset you just dialed up
blinks in the display. To conrm your selection, press the PROGRAM control;
theblinkingstops.
FX TO MAIN
The FX TO MAIN control feeds the eects signal into the main mix. If the control
is turned all the way counterclockwise, no eects signal is present in the sum
signal of the mixing console.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx QX1002USB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx QX1002USB in the language / languages: English as an attachment in your email.

The manual is 2,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx QX1002USB

Behringer Xenyx QX1002USB Quick start guide - English, German, French, Portuguese, Spanish - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info