496329

Behringer Xenyx 502 Manual

4
Zoom out
Zoom in
Previous page
1/12
Next page
4 XENYX 1202/1002/802/502 User Manual
1. Introduction
XENYX Mic Preamps
The microphone channels feature high-end XENYX Mic Preamps that
compare well with costly outboard preamps in terms of sound quality
and dynamics and boast the following features:
• 130 dB dynamic range for an incredible amount of headroom
• A bandwidth ranging from below 10 Hz to over 200 kHz for crystal-clear
reproduction of even the nest nuances
• The extremely low-noise and distortion-free circuitry guarantees absolutely
natural and transparent signal reproduction
• They are perfectly matched to every conceivable microphone with up to
60dB gain and +48 volt phantom power supply
• They enable you to use the greatly extended dynamic range of your
24-bit/192-kHz HD recorder to the full, thereby maintaining optimal
audioquality
“British EQ”
The equalizers used for the XENYX Series are based on the legendary circuitry of
top-notch consoles made in Britain, which are renowned throughout the world
for their incredibly warm and musical sound character. Even with extreme gain
settings these equalizers ensure outstanding audio properties.
Caution!
◊ We should like to draw your attention to the fact that extreme volumes
may damage your hearing and/or your headphones or loudspeakers.
Turn the MAIN MIX control and PHONES control in the main section fully
counter-clockwise before you switch on the unit. Always be careful to
set appropriate volume levels.
Important notes concerning installation
◊ The sound quality may diminish within the range of powerful
broadcasting stations and high-frequency sources. Increase the
distance between the transmitter and the device and use shielded
cables for all connections.
1.1 General mixing console functions
A mixing console fulls three main functions:
• Signal processing: Preamplication, level adjustment, mixing of eects,
frequency equalization
• Signal distribution: Summing of signals to the aux sends for eects
processing and monitor mix, distribution to one or several recording tracks,
power amp(s), control room and 2-track outputs
• Mix: Setting the volume level, frequency distribution and positioning of the
individual signals in the stereo eld, level control of the total mix to match
the recording devices/crossover/power amplier(s). All other mixer functions
can be included in this main function
The interface of BEHRINGER mixing consoles is optimized for these tasks enabling
you to easily keep track of the signal path.
1.2 The user’s manual
The user’s manual is designed to give you both an overview of the controls,
aswell as detailed information on how to use them. In order to help you
understand the links between the controls, we have arranged them in groups
according to their function. The illustrations at the beginning of each chapter
show the controls described in each respective chapter.
◊ The block diagram supplied with the mixing console gives you an
overview of the connections between the inputs and outputs, as well
as the associated switches and controls.
For the moment, just try and trace the signal path from the microphone input
to the FX send connector. Don’t be put o by the huge range of possibilities;
it’seasier than you think! If you look at the overview of the controls at the same
time, you’ll be able to quickly familiarize yourself with your mixing console and
you’ll soon be making the most of all its many possibilities.
If you need to know more about specic issues, please visit our website at
http://behringer.com, where you’ll nd explanations of (for example) eects and
dynamics applications.
1.3 Before you get started
1.3.1 Shipment
Your mixing console was carefully packed in the factory to guarantee safe
transport. Nevertheless, we recommend that you carefully examine the
packaging and its contents for any signs of physical damage, which may have
occurred during transit.
◊ If the unit is damaged, please do NOT return it to us, but notify your
dealer and the shipping company immediately, otherwise claims for
damage or replacement may not be granted.
1.3.2 Initial operation
Be sure that there is enough space around the unit for cooling purposes and to
avoid over-heating please do not place your mixing console on high-temperature
devices such as radiators or power amps. The console is connected to the
mains via the supplied cable. The console meets the required safety standards.
Blownfuses must only be replaced by fuses of the same type and rating.
◊ Never connect the XENYX to the power supply unit when the latter is
connected to the mains! First connect the power supply unit to the
console, then connect the power supply unit to the mains.
◊ Please note that all units must be properly grounded. For your own
safety, you should never remove any ground connectors from electrical
devices or power cables, or render them inoperative.
◊ Please ensure that only qualified people install and operate the
mixing console. During installation and operation, the user must have
sufficient electrical contact to earth, otherwise electrostatic discharges
might affect the operation of the unit.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx 502 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx 502 in the language / languages: English as an attachment in your email.

The manual is 2,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx 502

Behringer Xenyx 502 User Manual - German - 12 pages

Behringer Xenyx 502 User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info