542741
9
Zoom out
Zoom in
Previous page
1/12
Next page
ENGLISH
XENYX 1622FX/1832FX/2222FX/2442FX User Manual
16
ENGLISH
XENYX 1622FX/1832FX/2222FX/2442FX User Manual
17
wired in a balanced conguration. In case of doubt, contact
the microphone manufacturer!
Connect microphones before you switch on the
phantom power supply. Please do not connect
microphones to the mixer (or the stagebox/wallbox)
while the phantom power supply is switched on. In
addition, the monitor/PA loud-speakers should be
muted before you activate the phantom power supply.
After switching on, wait approx. one minute to allow
for system stabilization.
Caution! Please also note the information given in
chapter 6.2.1 Audio connections”.
SERIAL NUMBER
Please note the important information on the serial number
given in chapter 1.3.3.
INSTALLATION6.
Rack mounting6.1
The packaging of your mixing console contains two 19" rack
mounts for installation on the side panels of the console.
Before you can attach the rack mounts to the mixing
console, you need to remove the screws holding the left
and right side panels. Then, use these screws to fasten the
two rack mounts, each specically to one side. With the
rack mounts installed, you can mount the mixing console
in a commercially available 19" rack. Be sure to allow for
proper air ow around the unit, and do not place the mixing
console close to radiators or power amps, so as to avoid
overheating.
Only use the screws holding the mixing console side
panels to fasten the 19" rack mounts.
Cable connections6.2
You will need a large number of cables for the various
connections of the console. The illustrations below show the
wiring of these cables. Be sure to use only high-grade cables.
Fig. 6.1: Foot switch connector
Audio connections6.2.1
Please use commercial RCA cables to wire the 2-track inputs
and outputs.
You can, of course, also connect unbalanced devices to
the balanced input/outputs. Use either mono plugs, or use
stereo plugs to link the ring and shaft (or pins 1 & 3 in the
case of XLR connectors).
Fig. 6.2: XLR connections
strain relief clamp
sleeve
tip
sleeve
pole 1/ground
tip
pole 2
The footswitch connects both poles momentarily
1/4" TS footswitch connector
input
output
For unbalanced use, pin 1 and pin 3 have to be bridged
1 = ground/shield
2 = hot (+ve)
3 = cold (-ve)
12
3
1
2
3
Balanced use with XLR connectors
Caution! You must never use unbalanced XLR
connectors (PIN 1 and 3 connected) at the MIC input
jacks if you want to use the phantom power supply.
Fig. 6.3: 1/4” mono plug
Fig. 6.4: ¼" stereo plug
Fig. 6.5: Insert send/return stereo plug
Fig. 6.6: Stereo plug for headphones connection
Strain relief clamp
Sleeve
Tip
Sleeve
(ground/shield)
Unbalanced ¼" TS connector
Tip
(signal)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
Balanced 1/4" TRS connector
ring
cold (-ve)
tip
hot (+ve)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
Connect the insert send with the input and the
insert return with the output of the effects device.
Insert send return 1/4" TRS connector
ring
return (in)
tip
send (out)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
1/4" TRS headphones connector
ring
right signal
tip
left signal
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx 2442FX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx 2442FX in the language / languages: English as an attachment in your email.

The manual is 5,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx 2442FX

Behringer Xenyx 2442FX User Manual - Dutch - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info