660492
16
Zoom out
Zoom in
Previous page
1/29
Next page
16 X32 CORE DIGITAL RACK MIXER User Manual
5. Topic Guide
5.1 Firmware updates
The X32 CORE rmware can easily be updated by performing the following steps:
• Download the new console rmware from the X32 CORE product page onto
the root level of a USB thumb drive
• Plug the USB thumb drive into the front panel USB connector while the
console is turned o
• Hold the SCENE/SETUP button depressed while switching the console on.
While booting, the X32 CORE will run a fully automatic rmware update,
which will take 2-3 minutes longer than the regular boot sequence
When no update le is available on the USB drive, or when it is corrupted,
theupdate mode will remain active, preventing the X32 from booting regularly.
Switch the console o and back on without holding the SCENE/SETUP button to
boot the console with the existing rmware.
5.2 Remote control
The X32 CORE hosts an Ethernet port on its rear panel which can be used to
connect and remote control it over a network via the X32-Mix on an iPad or the
X32-Edit application on a PC. To be able to do this the X32 CORE has to be set
up properly.
• Enter Setup Mode by pressing and holding the SCENE/SETUP button
until the LED turns green.
• Rotate the Select knob to select “6. IP Address.” Press the Select knob
toconrm.
• Set an IP address which ts your network, normally 192.168.0.X.
Rotatethe Select knob to adjust the 1st triplet (0-255), then press to
conrm. Repeat this to enter the 2nd, 3rd and 4th triplet in the address.
The nal press will exit.
• Set your subnet mask according to your network, normally
255.255.255.0. Select setup page “7. IP Mask” and follow the same
procedure as the IP address.
• Set your gateway, if required, by selecting Setup page “8. IP Gateway”
and following the same procedure described above.
Now get your iPad or remote PC into the same network and open the X32-Edit.
PC:
• On the X32-Edit, choose setup on the right side and the network tab.
Enter the IP address of the X32 in the network and press connect.
• If the software has connected to the X32 you can also synchronize them
in 2 directions. Console -> PC means all settings in the X32 will be
loaded into the X32-Edit. PC -> Console means that all settings in the
X32-Edit will be written to the console.
X32-Mix
• For the X32-Mix remote, open the program on your iPad (make sure the
iPad is connected to the same network as the console).
• On the startup screen, a popup should appear. Enter the IP of the
console, press “Go Online”, et voilà: you are connected and can control
the X32 CORE with your iPad.
5.3 Recording a 2-track directly with
theconsole
The X32 CORE oers the possibility to record a 2-track of your mix (or any other
selection of signals) directly onto a USB-stick/external USB hard disk:
• Plug a FAT-formatted (FAT12, FAT16, FAT32) USB stick into the USB port
on the front panel.
• In your X32-Mix or X32-Edit software, navigate to the Recorder screen.
• On the cong tab you can select the source for the recording, default is
main L and R.
• Press RECORD (encoder #5) to record your mix.
• To adjust the volume during playback, use the virtual faders for Aux 7
and 8, which are assigned to USB playback by default.
Remarks:
Due to the FAT format of the stick, the le size will be limited to 2 GB, which is
about 3 hours of stereo recording. Please test the recording capability of your USB
device before you do the “real stu” as some sticks may not be supported or be
too slow. We also recommend you defragment your USB device prior to recording.
The recording will be done as 16-bit WAV le with the selected sample frequency
of the console.
Please also note that it is possible that the specications of USB storage devices
may be changed by the manufacturer without any change in physical appearance
or notication.
5.4 Saving and recalling scenes
Follow the steps below to save and recall scenes in the console, allowing dierent
congurations to be recalled at a later time.
• Adjust all settings of the console so that all elements of the mix are
asdesired.
• Select the Scenes menu in your remote software. The display will show
various controls for saving and recalling console scenes.
• Press the rotary control labeled “Save Settings” to save the console’s
current conguration to the next available empty scene and label it with a
customname.
• Adjust the console to the next desired conguration, and repeat the process
above as needed, saving additional scenes to additional empty slots.
• To recall a scene, scroll through the list of saved scenes. A gray box will
indicate which item is currently selected. When the desired scene is selected,
press the "GO" button and the console will switch to that scene. All console
parameters will switch to the state they were in when saved to the scene
that was just recalled.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer X32 CORE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer X32 CORE in the language / languages: English as an attachment in your email.

The manual is 4,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer X32 CORE

Behringer X32 CORE Quick start guide - English, German, French, Portuguese, Spanish - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info