660565
6
Zoom out
Zoom in
Previous page
1/11
Next page
6 VIRTUBE VT30FX/VT15FX/VT15CD User Manual
(11) The TREBLE control adjusts the treble frequencies.
On the VT30FX, the controls ( 9 ) , (10) and (11) are effective on the
OVERDRIVE channel only, since this amplifi er has a dedicated equalizer
for the CLEAN channel (see also ( 4 ) and ( 5 ) ).
(12) The VOLUME control adjusts the volume level of the OVERDRIVE channel.
2.1.3 FX section (VT30FX and VT15FX only)
(13) The FX LED lights up when the eects processor is active.
(14) Use the FX PRESET control to select one of 16 eects.
PRESET FX
1 - 4 Reverb
5 - 8 Delay
9 - 12 Chorus
13 - 16 Flanger
Tab. 2.1: Eects
(15) The FX LEVEL control adjusts the mix ratio between the original and
the eect signal.
2.1.4 Connectors and POWER switch
(16) The VTC push button activates and deactivates the VTC Virtual Tube Circuitry.
(17) The CD IN connector allows you to connect the output signal of a CD player,
tape deck, or CD/MD walkman. For example, you can play back music CDs or
CDs accompanying a guitar tutor while practising. This connector can also
be used as a LINE OUT output. In this case, the guitar signal is output with no
speaker simulation applied and can be routed to an external amp or mixing
console. This will not mute the built-in loudspeaker of the VIRTUBE.
(18) The LINE OUT/PHONES jack is for headphones connection. Internal speaker
simulation is applied to the headphones signal in order to produce an
authentic signal. The built-in loudspeaker of the VIRTUBE is muted when this
connector is used.
The headphones output signal can also be routed to a mixing console or
other sound reinforcement system. To do so, connect the headphones
output with the line input on the mixing console. Use a standard
cable with ¼" TS connectors. If hum problems occur, you could insert a
DI box, e.g. BEHRINGER ULTRA-DI DI100 or DI120.
With too high a volume level some headphones tend to produce
distortion. Please turn down the volume a bit, until distortion stops.
(19) Use the FOOTSWITCH jack to connect the ¼" TRS plug of the footswitch
supplied with the unit. The footswitch performs a dual function: it switches
between the two channels and turns the FX on and o (VT30FX only).
(20) The POWER switch turns your VIRTUBE on and o. It should always be
in the OFF position when connecting the unit to the mains. Please note:
Merely switching the unit o does not mean that it is fully disconnected
from the mains. To disconnect the unit from the mains, pull out the
mains connector. Before installation, please make sure that the mains
connector has not been damaged. If you do not use the unit for an extended
period of time, please disconnect it at the mains.
2.2 Rear panel
(22)
(21)
制造商
:
Behringer Holdings (Pte) Ltd
中国制造
(23)
Fig. 2.2: VIRTUBE control elements (rear panel)
(21) The VIRTUBE is connected to the mains using a standard IEC receptacle.
A suitable power cord is included with the unit.
(22) FUSE HOLDER/VOLTAGE SELECTOR. Before connecting the unit to
the mains, ensure that the voltage setting matches your local voltage.
Blown fuses must be replaced with a fuse of the same type and rating.
On some units, the fuse holder can be switched to one of two positions,
i.e. 230 V and120 V. Please note: when operating the unit outside Europe at
120 V, a higher fuse rating is required (see Chapter 4, “Installation”).
(23) SERIAL NUMBER.
3. Application Example
The VIRTUBE features plenty of connectors for a wealth of applications. Here’s an
example of how exible your VIRTUBE can be:
HPS3000
VIRTUBE VT30FX
CD Player
Drum Computer
CD In
Footswitch
Electric Guitar
Fig. 3.1: VT30FX standard set-up
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer VT15FX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer VT15FX in the language / languages: English as an attachment in your email.

The manual is 2,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer VT15FX

Behringer VT15FX User Manual - German - 10 pages

Behringer VT15FX User Manual - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info