656672
9
Zoom out
Zoom in
Previous page
1/24
Next page
9
ULTRALINK UL2000M
4. If a valid frequency value is set, press the SET button again. In the display, you are asked to enter
where you want to save your settings. Depending on the basic settings (ch. 2.2.5), the ULR2000 asks
you to enter a channel color (BLUE, RED, ...) or a channel number (CHAN1, CHAN2, ...).
5. A storage location can be selected by pressing the UP or DOWN buttons.
6. Press the SET button again to store your frequency at the location you selected. The procedure is
now over, and the basic settings are shown in the display again (channel number, channel frequency
or channel color).
A user-selected frequency is always stored in the user preset (Preset 1)! If necessary, the
unit automatically switches to this preset.
2.2.2 SCAN
Similar to a tuner in a radio or a TV set, the ULR2000 automatically searches for a transmitter when in SCAN
mode. For it to work, the transmitter (e.g. the ULM2000) must be turned on!
1. Press the SET button to get to the menu.
2. Press the UP button once to get to SCAN.
3. Press the SET button again to get to the SCAN submenu. The display shows the current frequency.
4. Either press UP or DOWN. This way, you determine if the scan is going to be performed in the
ascending or descending direction. The scan begins.
5. As soon as the ULR2000 recognizes the transmitter frequency, it is shown in the display.
If this frequency is not the frequency you were looking for, you can start a new scan by pressing the
UP or DOWN buttons.
6. If the receiver found the correct frequency, press the SET button again. In the display, you are asked to
enter where you want to save your settings. Depending on the basic settings, the ULR2000 asks you to
enter a channel color (BLUE, RED, ...) or a channel number (CHAN1, CHAN2, ...).
7. A storage location can be selected by pressing the UP or DOWN buttons.
8. Press the SET button again to store your frequency at the location you selected. The procedure is
now over, and the basic settings are shown in the display again.
A scan can also be halted manually (e.g. in case the receiver is unable to locate a transmitter).
To do this, press the SET button; the scan is immediately interrupted. Now, you can either
start another scan (see lines 4 and 5), or the frequency shown can be stored (see lines 6, 7
and 8).
2.2.3 SQUELCH
With wireless signal transmission, restricted reception conditions may cause the transmission of additional
noise and interference. The Squelch function lets you adjust if the ULR2000 is muted under such conditions.
You can also enter the noise level that will trigger the mute function:
0 dB: the receiver is not muted
low dB value: the receiver is muted only if substantial noise is transmitted with the signal
high dB value: the receiver is muted even if the noise floor is low
Setting a Squelch value
1. Press the SET button to get to the menu.
2. Press the UP button twice to get to SQELCH.
3. Press the SET button again to get to the SQELCH submenu. The display shows the current dB value.
4. Press the UP or the DOWN buttons to adjust the dB value of the noise limiter. Values between
0 and 40 dB can be selected in 5-dB increments.
If a squelch value of 0 dB is set, the receiver will not mute the signal no matter how noise-
saturated the incoming signal is.
5. Press the SET button to store your dB value. The procedure is now over, and the basic settings are
shown in the display again.
2. ULR2000 RECEIVER
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Ultralink UL2000M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Ultralink UL2000M in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Ultralink UL2000M

Behringer Ultralink UL2000M User Manual - German - 24 pages

Behringer Ultralink UL2000M User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info