810623

BeF Home Passive - HOT AIR FIREPLACE INSERTS Manual

8
Zoom out
Zoom in
Previous page
1/9
Next page
________________________________________________________________________________________________________________________________
Firma: BeF Home, s.r.o. Strana 8 (celkem 9) Platí od: 1. 4. 2014
Vydání: 4
Convection air:
To prevent heat accumulation, the incoming and outgoing grates of convection air must be open when using the fire. To prevent heat
accumulation in heat distributing system, length of horizontal distribution piping must not be longer than 2,5m. The piping must always lead up.
Exit can´t lead vertically down.
Fire protection above a heat radiation area:
A minimum distance of 5 cm from the outer space of the insert coating to non-combustible building panels must be retained (e.g. shelves)
Fire protection in a heat radiation area:
A minimum distance of 80 cm forwards and sideways must be retained in front of the firebox hole - (furniture, carpets,
plants etc.)
Protection against injuries:
Do not forget that heaters have hot surfaces. Use the enclosed protective glove when working with the fire. You could be in a heat radiation area
(80 cm) only during mending, and if there is further contact, the skin can be burnt. Keep the fireplace out of the reach of children.
Application and activation:
Permissible fuel and economic,emission-reducing operation:
The fireplace insert is designed to use wood as fuel. The water content is max. 20% of dry weight. Logs should be stored in a dry and well
ventilated place for two years. Using wet logs leads to smoke with a tar condensation which could damage the chimney. In any case there is
excessive environmental pollution. Logs should be 30 cm. Wood is a very gaseous fuel and needs a lot of secondary air. Regulation with the
help of slow or permanent burning is not possible with this kind of fuel. Heating output during wood burning is determined by the amount of the
fuel used. The most ecological and economical is dry wood burning because the heating quality of fresh wood is lower than that of dry wood. As
for burning waste, it must be stressed that burning material such as plastic material, cardboard, painted wood, etc. are harmful for your fireplace
insert and furthermore is prohibited by the Emission Act. It is allowed to use firelighters, paper and small wood for lighting a fire only.
Do not use combustible liquid e.g. petrol, alcohol for lighting a fire and do not store similar kinds of liquid near your
fireplace insert!
The first lighting:
The fireplace insert should start with a small fire at first, so as not to harm it by very fast temperature rise. Smoke and the smell of burning which
may appear during the first lighting of a fire is a result of coating thermal curing. The room should be well aired during first heating.
Before the first use, check if all removable parts of the fireplace (block, deflector, grate and ash hole) are in the
right position – in accordance with the Equipment Certificate.
Instructions for burning hot air inserts and stoves with an automatic monitoring of the combustion process.
- Read carefully the manual of automatic monitoring system of the combustion process.
- Set up the temperature of combustion and timing to start burning.
- Please use recommended firestarters only. Do not use liquidy firestarters or solid spirits ones either. Recommendable firestarter is coils
of wood wool with paraffin.
- Procedure of burning: put firestarter down on the hot tip. Make sure that the firestarter has provided enough air around. Surround
firestarter by a proper amount of wood (according to technical list of the fireplace insert).
- Burn out all wood until automatic monitoring system indicates to load more wood again.
- Make sure to always load up your fireplace by a proper amount of wood only. You can find more information in the technical data
document. This way you help to avoid overhating your fireplace.
- By following these inctructions you can use your fireplace as frequently as you need.
- Before next burning keep in mind that the firelace insert needs to be completaly cooled down. The display of automatic monitoring
system recognizes and indicates it and will show you right timing.
- The door of fireplace must be closed while burning. Otherwise the automatic monitoring system can not work propely which could
cause an overheated fireplace.
- Do not overload your fireplace by abundance of wood. Overloading of fireplace could cause an improper burning, dirty glass and even
damaged fireplace.
- The Optimum amount of fuel is recommended in the Equipment Certificate.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeF Home Passive - HOT AIR FIREPLACE INSERTS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeF Home Passive - HOT AIR FIREPLACE INSERTS in the language / languages: English as an attachment in your email.

The manual is 0.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info