768753
43
Zoom out
Zoom in
Previous page
1/70
Next page
Bébé Confort I Marble I 43
EN
SAFETY
The car seat is developed for an intensive use of
approximately 6 years.
Marble car use
After installing Marble correctly on the base, make
sure to position the car seat to the most rearward
position on the rear vehicle seat.
WARNING:
Install the car seat only rearward facing in the car on a
forward facing vehicle seat.
Marble and your baby
• Make sure you can fit no more than one finger
between the harness and your baby (1cm). If there is
more space than 1 cm, tighten the harness belt further.
• Make sure that the shoulder harness belts are at the
correct height. The shoulder harness belts should be on
or just below the baby’s shoulders.
• Only use the baby-hugg inlay of the Marble until
your baby exceeds the 60 cm length limit. Afterwards
remove the baby-hugg inlay from the Marble.
WARNING:
Never place the car seat on an elevated surface (such
as a table or chair).
Using Marble
In order to prevent the car seat from tipping over
during carrying, check if the carrying handle is locked in
place in carrying position.
• When Marble is installed on a stroller, always make
sure to use approved car seat adapters and to secure
Marble correctly.
• The height of the headrest and the shoulder harness
can be set simultaneously into 7 dierent positions.
Pull the headrest adjustment strap and meanwhile, pull
up or push down the headrest until it’s in the correct
position.
• The Marble can be put into 3 dierent reclining
positions by pressing the recline adjustment button and
meanwhile pulling the backrest down or up.
ATTENTION:
The reclining function can be used in the car until your
baby is 75 cm. After that, it is forbidden to recline the
Marble in the car.
Care advice
The cover, inlay, belt pads and sun canopy of the car
seat can be removed for washing. The front baleen of
the sun canopy needs to be removed before washing.
The harness webbing can be cleaned by using a wet
cloth.
A - Carrying handle
B - XL Sun canopy with peek-a-boo window
C - Push buttons for carrying handle
adjustment (L+R)
D - Stroller release buttons (L+R)
E - Marble (ISOFIX) base
E1 - Anchor points for securing seat
E2 - Car seat release button
E3 - Support leg with indicator for correct
installation
E4 - Release button for support leg
E5 - Indicator car seat locked in position (L+R)
E6 - ISOFIX connectors release buttons (L+R)
E7 - ISOFIX connectors (L+R)
E8 - ISOFIX connector indicators (L+R)
E9 - Base repositioning button
F - Harness adjuster button
G - Harness belt tensioner strap
H - Cover
I - Belt buckle with belt pad
J - Baby-hugg inlay
K - Shoulder belts with removable belt pads
L - Height adjustable headrest
M1 - Recline adjustment button
M2 - Storage compartment for user manual
M3 - Mounting bars for base
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bebe Confort Marble at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bebe Confort Marble in the language / languages: English, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info