766826
6
Zoom out
Zoom in
Previous page
1/26
Next page
5
DMX512 CONTROL
If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX
chain. Always connect the output of one unit with the input of the next unit until all units are connected.
CAUTION! At the last unit, you must close the DMX line with a terminating resistor. Take an XLR connector and solder a 120 Ohm resistor
between signal (-) and signal (+) and connect it to the DMX output of the last unit in the line.
DMX CHANNELS
CHANNEL
FUNCTION
VALUE
DESCRIPTION
1
Snow
000-001
No function
002-255 Snow output from 0-100%
2
Fan
000-255 Fan output level 0-100%
CLEANING
We recommend a frequent cleaning of the unit, in particular the output nozzle.
CAUTION! There are no serviceable parts inside the unit except for the fuse. Repairs and service operations are only to be carried out by
authorized dealers.
WARNING! Disconnect from mains before starting maintenance operation!
Ensure the fluid do not become contaminated.
Ensure the air vents are not clogged by dust. If necessary remove the dust.
Ensure that the unit can not get overheated.
Do not run the unit without any fluid, as the pump will run dry.
Wipe up spilled fluid immediately. Moisture and fluid can permanently damage the electrical components of the unit.
For cleaning the surface of the unit use a suitable, solvent-free cleaner.
It is recommended to run the unit on a monthly basis in order to achieve best performance and output condition.
Before storing, run distilled water through the system. This will help clean out the remaining snow fluid and prevent pump from
malfunction on next usage.
REPLACING THE FUSE
If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 160.756 SNOW 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 160.756 SNOW 500 in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info