765348

BeamZ 160.514 - ICE700 Manual

5
Zoom out
Zoom in
Previous page
1/20
Next page
5
FILLING FLUID TANK
Before filling disconnect from mains!
Step 1: Unscrew the cap of the fluid tank and to fill with original Beamz smoke fluid only. This fluid is environmentally friendly,
biodegradable and leaves no residue when used correctly.
Step 2: Replace the cap and close securely, ensuring the pipe is fed down to the bottom of the bottle.
Step 3: Open the ice reservoir cover by unscrewing fixation screw. Fill the reservoir with regular ice cubes and close the cover.
Step 4: Connect the mains plug.
OPERATION
Connect the power lead into the ice fogger machine and earthed mains outlet. Then you can switch the power
on by ON/OFF switch.
After a certain warm-up time, the ice fogger machine is ready to operate. Then the stand-by LED of the remote
control lights up. By operating the smoke switch on the remote control the low smoke emission starts. It may
happen that the stand-by lamp turns off and the smoke emission stops. In this case the device is heating up
again and will be ready to operate in approx. 1 min.
Switch off when ice fogger machine not used and unplug from mains if not use for long periods.
Attention: Drain the water in regular intervals (approximately every 30 minutes).
CLEANING
The ice fogger machine must be cleaned to avoid deposits in the machine, pump and heater.
Procedure:
1. Remove smoke fluid from the tank, fill “Beamz smoke machine cleaner fluid” (item no. 160.670) into empty tank.
2. Switch the power on and wait until smoke machine is warmed up.
3. Press on the button of remote control and pump the liquid through the machine.
4. Perform the above operation until the tank is empty.
5. Fill the tank with Beamz smoke fluid.
REPLACING THE FUSE
If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.
Procedure: Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.
ACCESSORIES
High quality smoke fluid on water basis, specially designed for Beamz smoke machines guarantees a trouble-free use.
5 liter packaging, ref. no. 160.582
1 liter packaging, ref. no. 160.643
Do not allow the pump to run dry!
Run clean procedure in a well-ventilated area!
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 160.514 - ICE700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 160.514 - ICE700 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info