766823

BeamZ 160.498 S3500 Manual

5
Zoom out
Zoom in
Previous page
1/24
Next page
5
SETTINGS
Via the Menu key, you can adjust the desired settings. After pressing the menu, the
display shows the following settings:
1. Man Vol Out xxx%.
Adjust the manual volume output within the range of 0% to 100% by means
of the Up/Down keys.
2. Interval Set xxxS
Adjust the interval between each fog emission within the range of 1 to 100S
by means of the Up-/Down keys.
3. Duration Set xxxS
Adjust the duration of each fog emission within the range of 1 to 100S.
4. Volume Out xxx%
Adjust the volume output during the timer function within the range of 0-
100%
5. DMX 512 #xxx
Adjust the DMX address for DMX control.
6. Wind For Class xx
NO FUNCTION for this smoke machine
7. Remote Out xxx%
Adjust the volume output during the remote function within the range of 0-100%
TIMER CONTROL
Press the Timer key to activate the timer function. The display shows the adjusted interval and the device counts the seconds
down to "0". After that, the fog emission is triggered at the volume adjusted under "Timer Out". The duration depends on the
settings adjusted under "Duration Set". If you wish to deactivate the timer function, press the Timer key once more.
MANUAL CONTROL (LOCKED)
Press the Lock switch (5) for immediate triggering of the fog emission at the volume adjusted under "Volume
Out". Press the Volume switch once more in order to stop the fog emission.
MANUAL CONTROL (100% OUTPUT)
Press the Manual key for immediate triggering of the fog emission at 100 % volume. Let the Manual key loose in order to stop
the fog emission.
DMX CONTROL
Connect the machine directly to a DMX controller or a DMX loop with multiple DMX effects. The machine uses a 3-pin XLR
connector for DMX connection.
Address Setup: Press the MODE button a number of times until Add appears on the display, with the UP / DOWN buttons the
start address may be set. The start address is defined as a first channel to which the machine will respond to. Check that there
are no overlapping channels used!
Note: It is necessary always lock the DMX loop with a 120 Ohm terminator for correct data transmission.
The DMX data will only be saved when display shows “Ready to Fog”.
CLEANING
After 40 operating hours, the smoke machine must be cleaned to avoid deposits in the machine, pump and heater.
Procedure:
1. Remove smoke fluid from the tank, fill “Beamz smoke machine cleaner fluid” (item no. 160.670) into empty tank.
2. Switch the power on and wait until smoke machine is warmed up.
3. Press on the button of remote control and pump the liquid through the machine.
4. Perform the above operation until the tank is empty.
5. Fill the tank with Beamz smoke fluid.
Run clean procedure in a well-ventilated area!
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 160.498 S3500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 160.498 S3500 in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info