766387

BeamZ 150.563 LCB144 LED Colour Bar Manual

5
Zoom out
Zoom in
Previous page
1/32
Next page
5
DMX CHANNEL MODE
You can control the fixture in two modes:
3 channel mode
5 channel mode
6 channel mode
12 channel mode
24 channel mode
48 channel mode
To adjust the setting:
1. Select “CHNd” MODE and press “ENTER”. The currently set option will blink in the display.
2. Use the “DOWN” and “UP” buttons to select 3ch, 5ch, 6ch, 12ch, 24ch or 48ch.
3. Press “ENTER” to save your selection.
BEHAVIOR WITHOUT DMX (DMX STATE)
The DMX STATE setting determines how the fixture behaves when it is not receiving a DMX signal. You can set the fixture to
enter Auto Mode, Sound Mode or black out.
To adjust the setting:
Select “SLNd” and press “ENTER”. You can choose between “Mast”, “SL1”, “SL2” and “d512”. For use the Auto or sound the
fixture must be set on “Mast”. When is select “SL1”, “SL2” or “d512” the fixture is black when without DMX.
2. Use the “Down” or UP buttons to select “Auto” or “Sound” and press “ENTER”.
3. When “Auto” you can choose between 16 auto programs select your program with de “Down” and “UP” buttons and press
“ENTER”.
When “ShNd” (sound programs) you can choose between 16 sound programs select you program with de “Down” and “UP”
buttons and press “ENTER”.
FIRMWARE VERSION
To display the fixture’s current firmware version, select “UER” and press ENTER. The display will show the version of firmware
in the fixture. Press MENU to exit.
IR MODE
Press mode key until Iron or IroF is displayed; then press Up or Down button to
choose Iron. Press ENTER to confirm.
To switch off the lights:
Press OFF on the remote control. All the lights will turn off until the button ON is
pressed [1].
Manual colour control
You can set R/G/B/W colours with the remote by pushing either the Red <R> button
for red, the Green <G> button for green, the Blue <B> button for blue [3].
Each colour intensity is then adjustable using the Light Up and Down [2] buttons
Preset colour mode:
Press one of the twelve preset colours on the remote control [4]. No dimming
possible with preset colours.
AUTO/SOUND on the IRC.
Press one of the four buttons to choose between the different auto programs. [5]
REPLACING THE FUSE
If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.
Procedure: Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 150.563 LCB144 LED Colour Bar at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 150.563 LCB144 LED Colour Bar in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info